How do I reset my electronic throttle control system?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.
How do you reset throttle body after replacing?
Leave the key off for a moment, turn the key to the "On" position again, wait 3 seconds, and press the accelerator 5 times in 5 seconds. Wait 7 seconds, and hold the accelerator down. The check engine light should start blinking, continue to hold pedal down until it stops blinking. You can then start the car.
How do you relearn throttle position sensor?
How to Reset Throttle Position SensorPut the key in the ignition.Turn the key to the On position, without cranking the engine. Wait a few seconds, then turn it off.Repeat the second step.Crank the engine.Pull the parking brake.Set the gear lever in Drive.Wait 5-10 minutes.
How do you relearn a procedure?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you'll need to perform a relearn procedure on the PCM. Here's how you do it start. And idle theMoreSo you'll need to perform a relearn procedure on the PCM. Here's how you do it start. And idle the engine in Park for 3 minutes initially. You may notice a higher incorrect idle speed until the ECM.
What happens if you dont reset throttle body?
If the TPS is causing your ECM to think that the throttle is closed when it isn't, it'll reduce the amount of fuel in the air/fuel mixture and cause the engine to run lean. Without enough fuel in the mixture, the engine will fail to make as much power as it normally does.
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.
How do you calibrate a throttle position sensor?
4:1410:54How to install & calibrate a new Throttle Position Sensor (TPS) #1208YouTubeStart of suggested clipEnd of suggested clipSo all we need to do just drop those pins. Down between the wire insulation. And the rubber grommetMoreSo all we need to do just drop those pins. Down between the wire insulation. And the rubber grommet that's there that's one you've got to go a long way down to get onto the contact.
How do you reset the throttle position sensor on a Ford f150?
Resetting the throttle position sensor is a simple process that can be done in just a few minutes.Find The Throttle Position Sensor. ... Disconnect The Electrical Connector. ... Unhook The Negative Cable From The Battery. ... Remove the Screws. ... Reconnect The Battery and Start The Engine. ... Regularly clean the throttle body and sensor.More items...•
How do you recalibrate a throttle body?
Accelerator Pedal Release Position Learning Procedure. Make sure that the accelerator pedal is fully released. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds.
Does a new throttle body need to be reprogrammed?
In fact, on some engines a new throttle body needs to be programmed with a factory, or equivalent, scan tool. The technician cannot even clean the carbon out of the throttle body in some cases without setting a “check engine” light.
How do I reset my throttle position sensor?
This step can also be necessary when you install a new sensor. The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
Do you have to calibrate a throttle body?
Once you have fitted a Throttle Position Sensor, or TPS, you will need to calibrate it from within MEITE. The signal on the chosen pin should sweep from approximately zero to five volts as you move the throttle from fully closed to fully open.
What happens when you unplug throttle position sensor?
The TPS as we call it is one of the most important sensors on the engine. Without it, the computer has no way of knowing when you push down on the gas or open the throttle. Best it can do it watch some other sensors and make some estimated guesses. On some cars, it may burp just as you unplug it if it’s running.
How do you relearn a Ford transmission?
With engine idling and transmission at operating temperature, apply foot brake and place transmission in Neutral. Wait 3 seconds, move shifter to D and wait 3 more seconds. Repeat 5 times, and move shifter to Park. Apply foot brake, move shifter to Neutral and wait 3 seconds.
How do you reset the computer on a Ford f150?
Loosen the lock nut located on the negative battery cable connector with a socket and ratchet. Pull the connector off the negative battery terminal. Wait for 20 minutes while the PCM bleeds off the electricity it stores for backup power. Once the power drains from the PCM, it resets.
How long to let a car idle?
Switch off all accessories. Fire the engine and run until it reaches operating temperatures and let idle for at least 1 minute. Turn the air conditioning on and let idle for another minute. Release the parking brake keeping Your foot on the brake pedal and the AC on. Let run another minute.
What is an ETB on a 2000 Ford?
Almost all 2000 Ford models now employ an ETB, or "electronic throttle body", that is controlled by the car's main computer. "Relearning" the ETB can help correct a rough idle and is often necessary after disconnecting the battery. likeAlternative. Like. (1)
How to relearning a car?
Turn the air conditioning on and allow the engine to idle for at least one minute. Release the parking brake. With your foot on the brake pedal and the A/C still on, put the vehicle in "D" (Drive) and allow the engine to idle for at least one minute. Drive the vehicle to complete the relearning process.
How to stop a car at a complete stop?
With vehicle at a complete stop, set the parking brake. Put gear shifter in "P" (Park), turn off all accessories. Run the engine until it reaches normal operating temperature. Allow engine to idle for at least one minute. Turn the air conditioning on and allow the engine to idle for at least one minute. Release the parking brake.