To remove an asphalt driveway, there are 4 major steps:
- Excavate the old asphalt using a machine that has ground-engaging tools to pull out all of the pieces. ...
- Install the gravel base – Unless your ground is extremely hard (rocky), you’ll need a gravel base under the new concrete. ...
- Lay down a 4-inch concrete slab. ...
- Pour the new asphalt mix or material of choice. ...
Full Answer
How to repair and reseal a driveway?
Instructions
- Wet the Concrete. Use a garden hose to wet the entire concrete surface. ...
- Add Concrete Cleaner
- Start the Pressure Washer
- Apply Concrete Cleaner Evenly
- Flush the Pressure Washer
- Wash With a Pressure Spray Tip and Water. After the concrete has dried for at least 24 hours, you can effectively apply a concrete sealer. ...
Should I repave my driveway?
Repave Your Driveway for Instant Curb Appeal. ... And if your driveway has lots of heavily cracked areas or large potholes, the gravel base probably needs repair; that’s a job best left to pros. If you decide to hire a contractor, avoid those who give bids over the phone. Good contractors will examine your driveway and give you a detailed bid.
What is the average cost to repair a driveway?
To confirm the integrity of a concrete driveway, hire a professional to address significant surface issues. The average cost to fix a concrete driveway ranges between $500-$1,100, with the average homeowner spending $800 to resurface a 250 square foot area, including labor and materials.
How to repave driveway?
When Is It Time to Repave or Replace Your Driveway?
- Asphalt. Asphalt combines stone and sand, and it uses a petroleum-based tar as the adhesive. ...
- Concrete. This type of driveway combines small stones and cement to make a hard surface. ...
- Brick or Cobblestone. As the name suggests, this driveway is made up of bricks or cobblestone. ...
- Gravel. ...
How do you get rid of a driveway?
Asphalt driveway removal can be accomplished using a jackhammer to break up the asphalt or even a circular saw to cut the driveway into small pieces. The best way to remove asphalt, however, is with a larger piece of equipment, such as a Caterpillar 303 excavator from a rental center.
What can I use to remove a concrete driveway?
While most of the work will be done by hand, you'll need a jackhammer to get started. Beginning in a top corner of your driveway, break concrete into small pieces and shovel debris into an out-of-the-way pile.
How much does it cost to remove existing concrete?
Most homeowners pay between $679 and $2,848 for concrete removal, with an average cost of $1,444. The national average cost of concrete removal is $1,444, with a typical range between $679 and $2,848 or between $2 and $6 per square foot.
How do you remove a concrete driveway by hand?
InstructionsDig Under the Concrete. Dig out the soil, gravel, or other material from under the concrete, using a shovel and a pickax or mattock. ... Strike the Concrete. Lightly sprinkle the concrete with water to minimize dust. ... Pry Off Stubborn Pieces. ... Move the Concrete Chunks With a Hand Truck.
Can I remove concrete myself?
Tearing up concrete yourself can also save you a ton of money. Hiring a contractor just to demolish a 12 x 14-ft. patio could cost you $1,400 or more. If you do it yourself, the cost to remove a concrete driveway will run you about $400, including rental and disposal.
How much does it cost to scrape a driveway?
Average Cost to Remove Concrete Driveway The national average cost to demolish a concrete driveway is between $500 and $2,500, including debris disposal and returning the site to grade. Concrete driveway removal costs $1-$3 per square foot on average, but your exact project cost could be more or less than this.
How long does it take to remove concrete?
On the low end, non-reinforced concrete at 3-inch thickness will take 0.030 hours per square foot, while on the high end, reinforced concrete at 8-inch thickness will take 0.098 hours per square foot.
How do I remove a concrete slab from my yard?
“Most concrete patios are un-reinforced, meaning that there is no rebar. So, in that case, a jackhammer is the best method to break the concrete into smaller pieces that can be shoveled away. If the area is very small, and the concrete is already cracked, a sledgehammer could also get the job done.”
How hard is it to cut concrete slab?
Wet concrete is very difficult to cut, and fully cured concrete can fracture as it's being cut. So if possible, cut concrete when it's hard but only half cured. The cut will come out smoother with less dust.
What tool do I need to break up concrete?
jackhammerA jackhammer is an ideal power tool used for concrete demolitions, and four subcategories of jackhammers exist, including rotary, demolition, combination and breaker options.
How do you remove old concrete?
Steps for Removing a Concrete SlabStep 1: Create a Void Under the Concrete. The best way to speed up concrete removal is to create a void underneath the section of slab you're working on. ... Step 2: It's Hammer Time. ... Step 3: Pull Apart and Remove the Broken Concrete. ... Step 4: Repeat Steps Until Concrete Is Demolished.
Can you use a hammer drill to break up concrete?
Hammer drills do not have a chiseling function and can be used to drill into a variety of materials. Rotary hammers use an electro-pneumatic hammer piston to generate high impact energy, which allows it to drill or demolish concrete.
What is a driveway made of?
Driveways can be made from a wide variety of different materials ranging from asphalt to gravel to river rock or just packed dirt. Over time, you may find that you want to replace the old driveway with something new, or you need to make repairs to specific sections. Removal depends entirely on what type of finish material was used in the completion of the finished driveway but generally involves the use of heavy equipment.
Can you rip up a driveway with cable?
Before you can rip up the old driveway with heavy equipment, you first need to contact the city to inspect your driveway and mark where any phone lines, cable lines or other utility lines may intersect with your driveway. Any damage done to city utility lines comes out of your pocket, not the city’s, which means you need to have city utility locations clearly marked in advance to avoid costly damages.
Can Hunker remove driveway?
Hunker may earn compensation through affiliate links in this story. Removing an asphalt driveway is a tough job that might cost you a lot of money if you decide to hire a professional. You can remove the driveway yourself--and you can make this tough job much easier--with the right equipment and some patience.
Can excavator buckets smash asphalt?
Advertisement. The excavator bucket can smash large asphalt chunks into smaller, more manageable pieces. Moving as much of the asphalt as possible into piles near shaded areas, or putting tarp over the asphalt, makes breaking up the asphalt into even smaller pieces with a pick ax or jackhammer an easier and cooler task. ...
How long does it take to remove a driveway?
Driveway removals can range from a week to a month long project depending on if you're working by yourself, availability of rental equipment and type ...
What is a driveway made of?
Driveways can be made from a wide variety of different materials ranging from asphalt to gravel to river rock or just packed dirt. Over time, you may find that you want to replace the old driveway with something new, or you need to make repairs to specific sections. Removal depends entirely on what type of finish material was used in ...
Can you rip up a driveway with cable?
Before you can rip up the old driveway with heavy equipment, you first need to contact the city to inspect your driveway and mark where any phone lines, cable lines or other utility lines may intersect with your driveway. Any damage done to city utility lines comes out of your pocket, not the city’s, which means you need to have city utility locations clearly marked in advance to avoid costly damages.
How much does it cost to remove a concrete driveway?
As the table shows, the cost to remove a concrete driveway varies quite a bit, from as low as $450 to as high as $4,000 or more in some cases.
Why is it important to hire a concrete removal contractor?
If the driveway removal is not handled properly , damage can be done to surrounding property or underground lines.
What are the factors that affect the cost of concrete removal?
The most common factors that affect the total cost of concrete driveway removal include: Size and depth of the driveway. Location and accessibility of the driveway. Local cost of living and debris disposal fees. Whether or not the concrete is reinforced.
Is it more expensive to remove a concrete driveway?
Naturally, the larger the driveway and the deeper the concrete, the more expensive it will be to break it up and remove it. Likewise, if your driveway is located in an area that has a high cost of living and high waste disposal or permit fees, then you can expect to pay more for your driveway removal.
Can you replace a cracked driveway with a new one?
Removing an old, cracked, or unsightly concrete driveway (and typically replacing it with a new driveway) can quickly improve your property's value, but you're likely wondering how much it will cost.
Does removing a driveway cost more?
And if your driveway is steep or surrounded by buildings or landscaping, it will take more time and effort to safely remove it, which will cost more as well. Another commonly overlooked factor that affects driveway removal costs is the contractor you hire to do it.
How much does an exposed aggregate driveway cost?
Exposed aggregate or pebble finish driveways cost $5 to $11 per square foot or $3,000 to $6,600 on average. Exposed aggregate features stones mixed into concrete or seeded on the surface. Natural aggregates provide a textured, nonskid surface in various colors, including pastels, earth tones, and deep reds and blues.
How much does it cost to install a concrete driveway?
Concrete driveway. Installing a concrete driveway costs $2,400 to $4,800 on average or $4 to $8 per square foot for plain gray concrete. Adding decorative colors, borders, stamped patterns, and finishes costs $8 to $18 per square foot. Concrete lasts 30 to 40 years and handles hot climates better than asphalt.
How long does a concrete driveway last?
Asphalt driveways last 15 to 30 years, and concrete driveways last 30 to 40 years on average, depending on the climate and usage. Brick and stone pavers last 25 to 50 years. A cobblestone or gravel driveway lasts up to 100 years if well-maintained.
What is the cheapest driveway material?
The cheapest driveway material is gravel at $1 to $3 per square foot using aggregate made of crushed shells, crushed concrete or asphalt, or pea gravel . Tar and chip seal driveways are the second cheapest at $2 to $5 per square foot.
How much does gravel cost?
Well-built gravel driveways require light raking and new gravel once or twice a year. Gravel prices range from $10 to $50 per ton, depending on the stone size and type.
How much does it cost to build a driveway?
The cost to build a driveway ranges from $600 to $18,000, depending on the material. The cheapest driveways cost $1 to $3 per square foot for gravel, while standard concrete and asphalt driveways cost $3 to $8 per square foot.
How much does a chip seal driveway cost?
Chip seal driveways cost $1,200 to $3,000 or $2 to $5 per square foot. Chip seal, also called tar and chip, lasts 7 to 10 years. Tar and chip driveways have the durability of blacktop, come in various colors, and feature layers of stone aggregate spread over hot liquid asphalt.