No, according to Bedford. “The sheathing will not project over the subfascia or real fascia,” he says. Be sure to install a drip edge, which deflects water away from the sheathing and fascia to prevent damage.
Does fascia go above or below roof sheathing?
Fascia outside Sheathing? - Fine Homebuilding Fascia outside Sheathing? I know that the fascia should go below the roof sheathing, but what about placing the fascia even with the sheathing? Here is the problem… the lookouts are already in place & the sheathing is installed.
Which side of fascia is flush with the sheathing?
In case I haven’t explained it well… the top edge of the fascia would be flush with the top surface of the sheathing. In case I haven't explained it well... the top edge of the fascia would be flush with the top surface of the sheathing.
Will a drip edge cover this seam in fascia?
As you said, the drip edge will cover the seam, so no problem there. If you are installing prefab fascia cover, however, it (the cover) might be too wide.
Is it time to replace your roof sheathing?
“If your roof sheathing has been damaged by water or the weather and is beginning to deteriorate in many locations, you should replace it,” says Bedford. This should be done as soon as you see damage because if you leave it alone, the condition of your roof sheathing will only grow worse, adds Robinson.
What is the top edge of fascia?
How long does cedar last on a roof?
Is a prefab fascia cover too wide?
Does hi- this work with asphalt?
Does shingle extension work?
Does sheathing overlap fascia?
In view A, the sheathing is started flush with the tail cut of the rafters. Notice that when the fascia is placed, the top edge of the fascia is even with the top of the sheathing. In view B, the sheathing overlaps the tail end of the rafter by the thickness of the fascia material.
How far should sheathing overhang fascia?
The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger. The shingles should also overhang the drip edge 3⁄8 to 1/2 an inch.
What goes on first roof or fascia?
Fascia and soffit are installed after the roof installation is finished. It is ideal that soffit and fascia materials be installed before you place tiles or any other type of roofing material on the roof.
How do you install roofing fascia and sheathing?
7:2516:58How to Install Sub Fascia // Roof Framing Part 7 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut anything over like a 5 12 pitch I like to put the bevel. On the fascia board and the reason whyMoreBut anything over like a 5 12 pitch I like to put the bevel. On the fascia board and the reason why we do that once we put our sheathing on top of here. 1 we need to nail the edge of our sheathing.
Should there be a gap between roof and fascia?
It's preferable to have the fascia or siding off of the roof by up to 2", like yours is. That gap is a little excessive for pvc in my opinion.
What goes on first fascia or drip edge?
The correct placement of a roof drip edge is on top of the roof's exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Should fascia be installed before shingles?
If your roofers are replacing your fascia board as part of a full roof replacement, then they will install the new shingles before they address the fascia. There is no way to replace the fascia board without removing the gutters, as the gutters are mounted to the board.
Do roof tiles rest on fascia board?
The tiles shouldn't be just rested on the fascia board as that is not what it is for, it's bad practice, and makes replacement fascia work harder.
What goes on first fascia or soffit?
The job goes smoother when you follow the correct installation sequence. First nail up the J-channel, then soffit panels, then fascia, then drip edge.
Can I attach a ledger board to a fascia?
If you own a two-story home, you can tie the ledger into a band joist. Find the band joist by measuring down from the 2nd story window. When you attach the ledger boards to the fascia, they should be held securely with bolts through the wall, or you can use lag screws.
Where do you start sheathing a roof?
0:392:55Roof Sheathing Installation Tips from Georgia-Pacific - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst ensure that the roof framing rafters. And upper truss cords are all in alignment. Use blockingMoreFirst ensure that the roof framing rafters. And upper truss cords are all in alignment. Use blocking to fix any areas of twisted framing and to provide a level surface for the panels.
Should I replace fascia before or after roof?
While it's always a good idea to replace damaged fascia as soon as possible, it is essential to ensure it is in good shape before a new roof is installed. Metal eaves drip is an important component in a quality roof installation project.
Does sheathing go over fascia? - AskingLot.com
When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia. This opens the door to the possibility of water damage by letting gravity work against you. Don't do that.
Roof sheathing overhang on fascia | DIY Home Improvement Forum
I make my own 3x3 custom bent to the roof pitch,so the gutter can be mounted to it-be sure to use gutter brackets w/galvanised screws to attach the gutter to the 3x3---w/this no ice can get under the flashing-if you are using ice+water shield install it to the top half of the 3x3 extended past 1/4",then use a hand roller to roll it down for good adhesion:thumbsup:
Roofing Sheathing/Plywood Overhang, Fascia thickness - NastyZ28.com
On my shed my sheathing does not protrude, Actually how both my house and shed are done is a 1 x 6 (house) 1 x4 (shed) fascia is installed to end of rafters, then 1 x 1 1/2 is tacked onto the fascia at the top.
New roof and Sheathing - Install new fascia before or after?
Hello, I own a 1950 home in southern california. I am in the process of removing two layers of asphalt shingles and one layer of wood shingles original to the home. After many hours I am almost ready to start installing new sheathing. The house has a hip roof with no soffits or gutters...
How far should roof sheathing overhang fascia?
Also Know, how far should Roof sheathing overhang fascia? It is at 45-3/4 in. Measure up the rafter 45-3/4 inch from the cut end of the truss tail and snap a line along the trusses. This indicates the upper edge of the first row of roof sheathing—leaving enough overhang that the subfascia and fascia will tuck neatly underneath when the time comes.
What is roof sheathing made of?
Roof sheathing is usually made of either oriented strand board (OSB) or plywood. Both materials are made of wood, but OSB is more lightweight and costs slightly less. Plywood is very durable but tends to cost a bit more and is heavier.
What does sheathing do on a roof?
The sheathing distributes weight evenly across the entire roof. Sheathing also provides a surface to which shingles are attached. Advertisement.
Why is roof sheathing important?
Unless you’re in the construction industry, roof sheathing isn’t typically a topic that enters everyday conversation, but it’s an essential component in protecting your family’s health and safety.
What is the best material for sheathing?
Plywood or oriented strand board, which is a type of engineered wood that’s similar to particle board, are the materials most typically used for sheathing, according to Bedford. Plywood is heavier and more durable, but oriented strand board, sometimes called waferboard, is less expensive.
Why is pressure treated sheathing preferred?
However, in some parts of the country pressure treated sheathing is preferred because of its resistance to termites. And some contractors appreciate the extra peace of mind its superior water resistance and durability offer. Advertisement.
Do homes need reinforcement during a tornado?
Homes in areas where hurricanes or tornadoes are common certainly need extra care paid to the sheathing’s ability to withstand heavy winds. Homes in less windy areas, on the other hand, might not need the same reinforcement.
How thick is a roof sheathing?
(on center) as the roof sheathing is span rated for 24″ O.C. . That sheathing is usually 1/2″ or even 7/16″ thick ply wood or OSB (oriented strand board aka wafer board that is APA (American Plywood Association) rated. The spacing of the actual framing member , rafter or truss, depends on it’s strength and the span of the member. Span being the distance between supports. So in most areas you’ll see the same sizing and span based on the span, however it is possible to have many different combinations to support the loads imposed on a roof. There is more than one way to skin a cat .
How many layers of fascia should I overhang?
If the fascia is to be one layer of 1x, I overhang the sheathing 5/8. If it is to be two layers of 1x or one layer of 2x, I overhang 1 3/8.
What is a hidden hanger?
Another is a “hidden hanger” that hooks inside the gutter and is also nailed through the face. The last would be a roof hanger that is nailed to the roof surface under the shingle tab. Now each of these methods have variants, but follow those particular attachment points. Related Answer.
Where should sheathing be on fascia?
Ideally the sheathing should be on top of the fascia without extending beyond it. Guesswork can create a situation in which it extends too far and it interferes with flashing installation, or you have to cut it.
Why do we need an overhang?
Because the axis of the earth is tilted, the sun angle varies with the seasons. It is possible to create an overhang that will let in the winter sun and keep out the summer sun — and the subsequent heat gain in the space. If the climate is warm all the time, and overhang will provide shade, and that alone will be cooler than being in the direct sunlight. In addition, an overhang will prevent the walls below it from getting direct sunlight, and having as much heat gain as they would otherwise.
Why does the sun angle change with seasons?
Because the axis of the earth is tilted, the sun angle varies with the seasons. It is possible to create an overhang that will let in the winter sun and keep out the summer sun — and the subsequent heat gain in the space. If the climate is
How many feet can a 2x4 span?
That may sound confusing, so as an example, the maximum span for a 2x4 should be 6 feet, since 4 times one and a half equals 6.
What is the top edge of fascia?
In case I haven’t explained it well… the top edge of the fascia would be flush with the top surface of the sheathing.
How long does cedar last on a roof?
the cedar will last the life of the roof, but if you're a true obsessive-compulsive like the rest of us here, dip them first in a sealer like thompson's, dry and apply
Is a prefab fascia cover too wide?
If you are installing prefab fascia cover, however, it (the cover) might be too wide.
Does hi- this work with asphalt?
hi- this works w any kind of roofing and will work in your application with asphalt architecturals
Does shingle extension work?
shingle extension also works if there is an undershoot/backflow condition where water backfeeds to rear of gutter, runs into fascia, down exterior walls see capes in my area where this occurs, lot of rot did floor repair recently h.o. did roof eave too tight, now a few years later i refinish floor, water seeped down fascia/wall/under bottom plate (skirtboard on house w/no cap flashing) rotted subfloor and got to a few oak strips replaced oak after blocking between joists, subfloor repair.... his summer project? extend roofline out, r&r rear wall of house
