Corner Bead under Tile. From what I've read elsewhere, you don't put corner bead behind tile. You just tape the greenboard corner and mud it square. But that's not really an option for the exposed drywall corners above the wainscot. Click to see full answer.
How do you put corner bead under tile?
Corner Bead under Tile. From what I've read elsewhere, you don't put corner bead behind tile. You just tape the greenboard corner and mud it square. But that's not really an option for the exposed drywall corners above the wainscot.
Do you put corner bead behind tile or behind chair rail?
If you don’t put corner bead on the corner behind the tile, then the corner bead above the chair rail will flare out anyhow, and the flare will be noticeable when the corner bead covers up part of the top of the chair rail. From what I’ve read elsewhere, you don’t put corner bead behind tile. You just tape the greenboard corner and mud it square.
What is the best corner bead to use?
The most common and least expensive corner bead is galvanized metal. Vinyl Corner Bead. Vinyl corner bead is the plastic version of metal and is less prone to transport damage. Drywall J-bead & L-bead.
Where do you put corner bead on a wing wall?
Normally, on a drywall wall, you would put corner bead on both outside corners of the wing wall, from the floor to the ceiling. However, if you’re tiling the wall and install corner bead first, the corner bead will make the end of the wall flare out at least 1/16″ on each side, and probably more like an 1/8″.
How do you tile over corner bead?
0:148:07Prepping a corner bead and where cement board and sheetrock meetYouTubeStart of suggested clipEnd of suggested clipFor them and so what I did here is i when the corner bead was off I stuck a piece of cement.MoreFor them and so what I did here is i when the corner bead was off I stuck a piece of cement.
Do you need corner bead inside corner?
The answer, though, is simple: They cheat. They use a rigid material called corner beading, which can be made of metal or plastic. Inside corners don't need as much protection, so drywallers cover them with regular drywall tape. The process for finishing inside and outside corners is the same.
How do you transition from drywall to tile?
2:109:14BACKERBOARD/DRYWALL Transition Tile Shower WallYouTubeStart of suggested clipEnd of suggested clipSo there's a couple ways to waterproof. This you can either use sheet membrane. Like this rss sheetMoreSo there's a couple ways to waterproof. This you can either use sheet membrane. Like this rss sheet membrane or kerdi. And you would just cover the transition. Like so up to the black sharpie.
What is the purpose of a corner bead?
Corner bead is used in drywall finishing for two reasons: to stabilize and reinforce corners and to cover the visible seam between the two separate drywall boards, creating a seamless 90-degree angle.
Can I use tape instead of corner bead?
For me, outside corners are a lot easier to tape than inside corners. There is no need to put any tape on the corner bead (though you can tape the edge of metal corner bead to reduce corner cracking). In addition, there are usually no seams or gaps along the corner bead edge (if there are gaps, use joint tape).
Where do you put corner bead?
0:255:30How to install a corner bead. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo first we're going to take a look at the standard steel bead a bead like this should be installedMoreSo first we're going to take a look at the standard steel bead a bead like this should be installed using screws nails or a hammer and clincher mm it to the corner.
What should I put between drywall and tile?
The best product to use under tile in wet areas is cement board. This is similar to drywall in that it comes in sheets, but cement board will not develop mold or deteriorate when exposed to water.
Should I caulk between tile and wall?
Caulk seals seams between tile and fixtures or walls. Caulk provides a waterproof seal where tile abuts other materials, such as bathtubs, sinks, or walls. A carefully run line of caulk (known as a bead) in these areas adds a finished touch.
Should tile be flushed with drywall?
Tile and drywall is not supposed to be flush. Yours looks a little off because you have not put a row of bullnose tile to round into the drywall.
Should I use metal or plastic corner bead?
Besides the daily wear-and-tear that your average drywall corner is going to sustain over the years — accidents happen all the time, of course, and vinyl beads can withstand impact much better than metal — metal beads can be easily damaged during transport if they are crushed or jostled.
Which is better paper or metal corner bead?
Outside drywall corners have traditionally been protected with nail-on metal corners, but paper-faced corner bead is simpler and resists cracks and chips better.
What's better metal or vinyl corner bead?
1:426:08Smash Test: Vinyl Vs. Metal Corner Beads! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWere were quite the same. But you can see the damage is very different on both the metal corner beadMoreWere were quite the same. But you can see the damage is very different on both the metal corner bead. And the vinyl corner bead now let me show you exactly why the vinyl damage is going to be much
How to repair cracks in cement?
Step 1: For holes larger than 1/2-inch in diameter, use a carton knife or carbide-tipped tool to cut a V-shaped groove behind the edges of hole. Step 2: Use a clean, damp sponge to wipe down the area to be patched.
Is cement board wet or dry?
The cement board is on the wet area, the drywall is on the dry area, forming an outside corner. Are you saying just use the metal/paper corner bead, install with drywall mud, even on the cement board. Then, just tile over the mud with thinset & tile. Click to see full answer.
Step 1
Measure the height of the wall where the corner bead will be installed. Record the measurement. Transfer that measurement onto the first piece of corner bead and mark the cut location with a black marker.
Step 2
Cut along the line with a pair of tin snips. Snips cut just like scissors. Set the corner bead back into place and verify that the proper height measurement was cut. Push the piece into the corner where the Durock butts together from each side of the wall.
Step 3
Line up the first cement board screw along the top of the corner bead. Find a pre-drilled hole in the corner bead and push the screw into the hole. Attach a drill bit to a power drill. Secure the screw in place through the hole and into the Durock.
Step 4
Drill until the head of the screw is flush with the corner bead. Move to the same level on the other side of the corner bead and repeat the same process. Move down 8 inches and insert another screw on each side. Continue in the same manner down the corner bead, inserting a screw every 8 inches on each side.
Step 5
Inspect the corner bead and verify that it is securely attached to the Durock. Repeat the process for any of the other corners in the room where you want to have corner bead.
