Receiving Helpdesk

do you have to drain pool to change light fixture

by Verla Mosciski Published 3 years ago Updated 2 years ago

Fortunately, the answer is no—the water typically does not need to be drained! Because the electrical cable is sealed, it's impervious to any water that will get into the conduit when the bulb is being replaced.Mar 3, 2021

Do I have to get into the pool to change the light?

If you can reach the screw holding the light assembly in place from outside the pool, you don't have to get into the pool to change the light. Thanks! Do I have to drain a pool to change the light bulb?

How do you set up a pool light fixture?

The majority of pool light fixtures have a surplus of wire to allow you to remove it from the pool and set it down on the deck. Grab one of the towels you brought to set it on in order to avoid accidental lens scratching.

How do you replace pool light bulbs?

You can purchase replacement pool bulbs through major online retailers or through the pool manufacturer’s website. If you’re worried that the light fixture may be leaking, you can also purchase a new rubber gasket to seal the fixture and prevent water from getting in.

How do you change the light on a pool niche?

To change a pool light, start by shutting off all power to the pool using your home's circuit breaker. Then, remove the screw at the top of the lighting fixture and use a flat-head screwdriver to pry the fixture out of the niche box.

Do you have to drain a pool to replace a light?

Replacing pool lights for your in-ground swimming pool does not require draining the water from the pool or hiring a professional. The design of the pool light's housing allows you to remove it from the pool without the need to disconnect any wiring.

Can you change a light in a pool with water in it?

Just like any light, the bulb can burn out and will need to be replaced. There is no need to lower the water level in your pool to replace the burned-out bulb.

How do you replace a pool light fixture?

2:175:36How To: Replace a Pool Light Fixture - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemove the light fixture off the pool wall it is generally secured by one screw at the top of theMoreRemove the light fixture off the pool wall it is generally secured by one screw at the top of the light fixture. Pull a light fixture out of the niche.

How do you change a light in an inground pool?

Safety always being the number one priority, be sure to read all the instructions before you begin, and don't skip any steps.Turn Off the Power. ... Remove the Pilot Screw from the Light. ... Pry out the Fixture. ... Test the Wiring. ... Take the Fixture Apart. ... Remove the Old Light Bulb. ... Add the New Light Bulb. ... Test the Light.More items...•

What happens if water gets into pool light?

Water inside the Pool Light? If there is water inside the lens of the pool light, which you can usually see from on-deck, that doesn't mean that the light is leaking, but it does mean that the lamp gasket has failed, letting water leak inside and surround the bulb.

Can a pool light electrocute you?

You can get electrocuted by a pool light where faulty wiring or defective lighting equipment causes an electrical current to be released into the water and you come into contact with the electrified water.

How much does it cost to replace pool light fixture?

The smaller LED lights like the Pentair Globrite or PAL 2000 typically cost between $700 and $900 installed. Fiber optic pool lights are usually around $1,300 to $1,700 installed. Full size incandescent pool lights are typically in the range of $450 to $650.

How do you install a pool light?

1:407:42Poolside Repair: How To Install A Pool Light - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to be taking the epoxy out of the niche. Yeah and the epoxy it's a it's a very hard andMoreWe're going to be taking the epoxy out of the niche. Yeah and the epoxy it's a it's a very hard and tough it's actually at the top on this one where the conduit is sometimes in the back.

Do pool lights need to be grounded?

An electrician should ground the light niche, to protect against any stray voltage. Inside the wet niche there is a grounding lug that must have a bare copper wire connected to it, normally this a continuous ground around the entire pool.

How do you upgrade an old pool light?

1:003:10How to: Upgrade Your Pool Light To an LED Color Changing LightYouTubeStart of suggested clipEnd of suggested clipRemove the gasket from the lens. Clean the lenses rim. And face before reinstalling into the fixtureMoreRemove the gasket from the lens. Clean the lenses rim. And face before reinstalling into the fixture. Now we can remove the bulb from the fixture by simply unscrewing.

How do I change the LED light in my pool?

What Are The Steps Involved?Step 1: Safety First! Turn Off the Power. ... Step 2: Remove the Top Screw from the Light. ... Step 3: Pry the Light Fixture Out. ... Step 4: Test the Wiring. ... Step 5: Take the Fixture Apart. ... Step 6: Remove the Old Light Bulb. ... Step 7: Screw in the New Light Bulb. ... Step 8: Test the Light.More items...•

How long do inground pool lights Last?

Your pool lighting should give you few problems overall. Most incandescent bulbs will burn for 1,000 hours before bulb replacement is necessary. LED bulbs can burn for 25 years or more (or so they tell us).

Do you have to drain your pool?

An example of when to drain your pool. In summation, the rule would normally be: No, you don’t have to drain water except for that rare instance. 98% of the time you don’t have to drain the water, other 2% bring your floaties.

Can water get into an electrical cord?

Water is not going to get into the electrical cord. That’s why they also recommend don’t splicing. Don’t splice the cord because then you risk water touching inside of the cable. There are times when draining the pool would be necessary. Like if your pool was on a hill.

Is pool light cable sealed?

The cable on the pool light fixture is sealed and there always tends to be water inside that conduit. Even if you do drain, water gets into that conduit. Like I said, the cable is sealed. It runs all the way through the conduit and it terminates above ground into a junction box.

How to know what light bulb to use for pool?

Here, wattage and voltage are especially important. To work out which light bulb model you need, you can pull out your pool user manual to find out the exact type of bulb the fixture requires. Make sure that the new one you buy matches the size, brand, and serial number.

What to do if you don't see the switch in your pool?

If you don’t see the right switch in the main electrical box, have a look around your pool equipment to find the right box. Once you’ve checked that the power is off and no electricity is running to the pool… check it six more times. Getting electrocuted is not part of the process.

How to remove old gasket from pool lens?

Take care when disassembling these pieces and make sure not to drop anything in the pool. Grab a damp rag to remove any old gasket residue from the surface of the lens.

How to check if pool breaker is turned off?

Grab your voltage tester (multimeter) before touching the wires with your hands and test to make sure there’s no electricity running through there. If you’re multimeter registers anything, that means something hasn’t been turned off. Double-check your that your pool breaker is turned off before going on to the next step.

How to loosen a cord on a light fixture?

If the cord doesn’t unravel easily, grab the cord closer to the wall and try giving it a few gentle tugs to loosen it. (Note how the excess cord is stored so you can replace it the same way when you’re reinstalling the light later on.)

How to turn off the power to a pool?

The first (and most important step) is to turn off all power to your pool. Most commonly you’ll have a switch in your home’s circuit breaker box labeled “pool”. Switch this to the off position and then try to turn on the pool lights to make sure there is no power.

How long does it take for a pool light to burn out?

Just a quick peek to make sure the new bulb works and then turn the electricity right back off. If you leave the light on for more than 5 seconds , there’s a chance the bulb will burn out. Normally in the pool, these halogen bulbs have the water to cool them off. So without the water, they get extremely hot.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9