Are there any problems with the Minn Kota trolling motor?
AutoPilot and Spot-Lock Issues These defects can be significant, as AutoPilot and Spot-Lock are the most popular features on GPS-enabled trolling motors. You want it to work every single time while on the water. Some Minn Kota models have the following problem while using the AutoPilot: the motor stays on when you try to switch it off.
Why does my Minnkota trolling motor blow fuses?
Minnkota Trolling motor blows fuses. The problem is that the fuse is to small. The motor is pulling 50 amps at high speed therefore you should have a 60 amp inline fuse with manual reset circuit breaker.
Where do the fuses go on a Minn Kota?
The transom ( gas ) motor has the fuses in line to the power switch before it goes to the battery. But the Minn Kota not having a safeguard from the factory is a big disappointment. I will get back to you in the next couple of weeks. Thanks for the tips and the help about my concern.
Do I need a fuse for my trolling motor?
You don't want a fuse unless you want to carry a bag full of fuses with you on the lake. Even an normally operating trolling motor can occasionally blow a fuse.
Does a Minn Kota need a fuse?
It is highly recommended that a circuit breaker or fuse be used when installing a trolling motor. Refer to the Minn Kota “Conductor Gauge and Circuit Breaker Sizing Table”. For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended.
Do trolling motors have a fuse?
You've probably heard that you need to install a fuse or circuit breaker on your trolling motor. Both fuses and circuit breakers work to prevent the electrical system from overheating and damaging the wires or other components.
How do you reset a trolling motor circuit breaker?
1:353:52How to Check Your Trolling Motor Breakers - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can almost see you have two posts. One and two okay let's connect it on the positive. And thisMoreYou can almost see you have two posts. One and two okay let's connect it on the positive. And this little bitty black button over here getting closer that is the reset.
Why am I not getting power to my trolling motor?
Loose Connection A loose or broken wire is one of the most common problems if you have no power to your trolling motor. Often, the vibrations that come with repeated uses will cause wires or other parts to shake loose, killing the electrical circuit.
How do you reset a Minn Kota trolling motor?
0:191:20How to reset Ulterra Trim and Stow | Minn Kota | The Technological AnglerYouTubeStart of suggested clipEnd of suggested clipThe factory spec here is to press the power button three times within two seconds. This willMoreThe factory spec here is to press the power button three times within two seconds. This will initiate the recalibration.
Why do you need a fuse for a trolling motor?
Why Your Trolling Motor Needs a Circuit Breaker A circuit breaker works by “tripping” the circuit whenever there is too much current flowing towards the motor. This overload happens when your prop gets stuck in weeds, rocks, etc., and can't rotate freely.
Can you run a trolling motor without a circuit breaker?
Yes, you must install a circuit breaker when using a trolling motor, even though the battery would power the motor without it as well. There are several reasons. First, trolling motor manufacturers require the use of circuit breakers. Not using one will void your warranty.
How do you reset a marine circuit breaker?
0:100:47Resetting the Circuit Breaker on Hewitt Hydraulic Pontoon LegsYouTubeStart of suggested clipEnd of suggested clipOn the front of the plate here on the front of the motor is the breaker. This red button here that.MoreOn the front of the plate here on the front of the motor is the breaker. This red button here that. Now I actually tripped the breaker if you press it just a little lever will pop out.
What size fuse do I need for my trolling motor?
What is this? To be exact, a 50-amp circuit breaker for a trolling motor and a 60-amp circuit breaker for a trolling motor should always handle more than 10% of the current requirement of the motor.
What is the problem with Minnkota trolling motors?
Minnkota Trolling motorblows fuses. The problem is that the fuseis to small. The motoris pulling 50 amps at high speed therefore you should havea 60 amp inline fusewith manual reset circuit breaker.
How does a trolling motor work?
Working Of Trolling Motor The foot, speed and steer controls are in the foot panel. The trolling motor is mounted on the boat by using the mounting mechanism. The wires reach the motor, lining up to the shaft, which provides a depth to the motor. When the current is put on, it reaches the motor.
How to reset Ulterra motor?
In the unlikely event Ulterra will not trim or stow, the following procedure will reset the motor and restore functionality: 1 Press and hold the POWER button located at the mounting base to turn power off (green LED light will turn off). 2 Press the POWER button until the green LED light illuminates. 3 Wait 3 seconds.
How to put a Talon in manual retraction mode?
a) Press and hold the Up button on the Indicator Panel until you hear 3 successive beeps. This will put the Talon in Manual Retraction Mode.
How to pair a Micro Remote?
To pair your Micro remote, please follow these steps: Power up the trolling motor. Push and hold the learn or pair button down on trolling motor head. While continuing to hold the learn or pair button, push and hold the High Speed Bypass and AutoPilot keys simultaneously on micro remote for up to 3 seconds.
Why disconnect motor from battery?
For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteries are being charged. Improper wiring of 24/36/48-volt systems could cause battery explosion! Keep wire wing nut connections tight and solid to battery terminals.
What terminal is the connector cable on a battery?
Connect a connector cable to the negative (-) terminal of battery 1 and to the negative (-) terminal of battery 2.
Can metal fall on trolling motor?
Take care that no metal object can fall onto the battery and short the terminals. This would immediately lead to a short and extreme fire danger. It is highly recommended that a circuit breaker or fuse be used when installing a trolling motor. Refer to the Minn Kota “Conductor Gauge and Circuit Breaker Sizing Table”.
Can you use a crank battery on a Minn Kota?
If using a crank battery to start a gasoline outboard, we recommend that you use separate deep cycle marine battery/batteries for your Minn Kota trolling motor.
How to wire a trolling motor?
How to Choose a Trolling Motor Circuit Breaker? How to Wire a Circuit Breaker For a Trolling Motor. Step 1: Find a Good Location to Mount Your Circuit Breaker. Step 2: Mount the Circuit Breaker to a Suitable Surface. Step 3: Connect the Motor to the Circuit Breaker. Step 4: Connect the Battery.
How to Choose a Trolling Motor Circuit Breaker?
There are two main things to look for when selecting a circuit breaker for your motor: Current rating and voltage range (dc).
Why is my trolling motor overheating?
This excess current can cause overheating and damage to your trolling motor. An overload could also happen when your wiring is inadequate, for instance, when the wire is too long and the wire gauge too small for the current it is supposed to carry.
Why do trolling motors need a circuit breaker?
Why Your Trolling Motor Needs a Circuit Breaker. A circuit breaker works by “tripping” the circuit whenever there is too much current flowing towards the motor. This overload happens when your prop gets stuck in weeds, rocks, etc., and can’t rotate freely. The motor will then start to draw more current in an attempt to increase power.
What is an inline fuse?
Inline Fuses for Trolling Motors. Fuses serve the same purpose as circuit breakers – they prevent overloads in electrical circuits. However, they work in a very different way. A fuse is made of a thin piece of metal that overheats and melts when too much current flows through it.
Do you need a breaker for trolling motor?
If you just bought your trolling motor and want to wire it properly, do not forget to install a circuit breaker or a fuse. It doesn’t cost much and will protect your investment.
Can fuses be reused?
Since fuses are destroyed by heat, they can’t be reused like circuit breakers and must be replaced.
Minnkota Trolling motor blows fuses
Last year someone posted a similar problem to a problem I was having with a new trolling motor I installed on my boat. When I took my boat out of the water for the season I discovered that the wire on the fuse link was melting.
Re: Minnkota Trolling motor blows fuses
I had this same problem when I installed my new All Terrain 50 ft/# thrust Minn-kota trolling motor on my Fishermarine Water Strider III bass boat.
How to use i-pilot trolling motor?
With an i-Pilot trolling motor, you can steer, control speed, lock onto fishing spots, and more just by pressing a button on the remote from anywhere on your boat or even from a distance.
What is the most popular feature on GPS trolling motors?
These defects can be significant, as AutoPilot and Spot-Lock are the most popular features on GPS-enabled trolling motors. You want it to work every single time while on the water.
Why won't my motor start?
One of the most common reasons is not enough voltage reaching the motor. This could be due to bad batteries or incorrect wiring.
Why is my foot pedal not working?
If your foot pedal doesn’t work correctly, it could be that it got slightly out of shape, and the buttons are pressed when they shouldn’t be .
What mechanism does a Terrova use?
The Terrova uses a spring-loaded lift assist mechanism, which can cause it to bounce in and out of water.
Does Minn Kota have a lifetime warranty?
On the plus side, the shaft is strong and comes with Minn Kota’s lifetime warranty. That means the company will pay for the replacement if it ever gets damaged, no matter how it happens.
Can you use a propeller for bass fishing?
Many anglers like this propeller as it’s great for bass fishing, but if you go and buy it separately, you will be disappointed again. It won’t fit as it’s simply too big.
