How does a B vent gas fireplace work?
A large part of a successful gas fireplace installation is the selection of the proper vent pipe to route the burnt exhaust gases to atmosphere. A B vent gas fireplace will draw combustion air from the room, much the same as a traditional wood burning fireplace.
What makes a successful gas fireplace installation?
A large part of a successful gas fireplace installation is the selection of the proper vent pipe to route the burnt exhaust gases to atmosphere. Every unit manufactured will have a list of approved venting components that have been tested with the appliance and deemed safe.
What size ventilation brick do I need for a gas fire?
Fitting a flueless gas fire requires that a 100cm 2 ventilation brick be fitted on an external wall in the room where the fire is fitted. Also, depending on the fire, the room must be a certain size, generally between a minimum of 25 – 30 cubic metres.
Do you need a chimney for a direct vent gas fireplace?
Even better, with a direct-vent gas fireplace no sizable chimney is required, making it possible to install a gas fireplace quickly and easily into many existing buildings. Because you'll be working with gas, however, it's important to have a good understanding of how to install a gas fireplace before beginning any installation project.
How much does it cost to have a gas fire installed UK?
On average, you're looking to pay between £100 – £200 to install your gas fire. Other costs to consider are annual servicing of the fire which costs on average between £60 – £100. As there is gas involved, it's also worth ensuring you have a carbon monoxide sensor installed in the room.
Can I install a gas fire myself?
While it may be tempting to connect a gas fire to your system on your own, it is illegal and dangerous. Given this, it is important to add an installation fee to your budget. Though most retailers also offer installation services, this easy route may not be the most affordable.
Is it worth installing a gas fire?
Open Fire vs Gas Fire Efficiency Open fires burn up fuel quickly and inefficiently – in fact, they have an efficiency rating of just 30%! Gas fires, on the other hand, can be almost three times as efficient. While the flames may seem more subdued, they actually push more heat into your room.
How long does it take to install a gas fire?
If you're installing a freestanding gas fire, this could take as little as a few hours. If you're retrofitting a gas fire into an existing chimney, this might take a bit longer depending on the brick work and accessibility for the new flue (allow up to two day for this type of install).
How much does it cost to have a gas fire on?
Typically, with gas fires it only costs around 5 pence per KW to run – when compared to electric which typically costs around 15p per KW and bioethanol which can cost up to 90p per KW, this is by far the most efficient.
What is the average cost of a gas fireplace insert?
The average cost of a gas fireplace insert is $1000. There are many factors to consider when purchasing a gas fireplace insert, such as size, type, and features. The average cost of a gas fireplace insert is $1000, but it is important to find the right one for your needs.
Are gas fires being phased out?
Gas hobs, cookers, fires and boilers could all be phased out within 15 years, with households dumping appliances. All gas-fired power stations must also close by the mid-2030s, unless they manage to remove CO2 from their emissions.
Does British Gas supply and fit gas fires?
Over the years most people have had a gas fire supplied and installed by British Gas. They were the go to for all gas appliances and still are in many cases, although these days servicing is their main area of business. For those looking for a trusted alternative then maybe we can help.
What is the best gas fire to buy?
The Best Gas Fires 2020…Verine Passion High Efficiency Gas Fire.Verine Meridian High Efficiency Gas Fire.Eden High Efficiency Hole In The Wall Gas Fire.Eko Fires 4010 Efficiency Gas Fire.Be Modern Design Fascia Mid Depth High Efficiency Gas Fire.
How often should you replace a gas fire?
Generally speaking, you can get a good ten to fifteen years of use before you need to replace your gas fireplace.
Can you fit a gas fire without a chimney?
Standard gas stoves A regular gas stove does need a chimney or flue. As gas doesn't produce any heavy smoke, as a wood burning stove would, they don't require you to have a Class 1 brick chimney – though they usually can be installed into one of these without any issues.
How do you fit a new gas fire?
0:1321:35Installing an inset gas fire - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo he's always important to make sure that you've checked the integrity of the chimney beforeMoreSo he's always important to make sure that you've checked the integrity of the chimney before installing a fire because you don't want to be installing a fire when the chimney is no good.
What is a B vent?
There are three venting options available for gas fireplace installations: Natural vent, often called B vent, utilizes an existing masonry chimney or a factory-built metal chimney. Room air exhausts combustion by-products to the outside via a flexible liner or single pipe installed within the chimney.
HOW MUCH HEAT DOES A GAS FIREPLACE PUT OUT?
He also points out that “a lot of high-efficiency gas fireplaces have a large turn-down ratio—meaning, they can go from 40,000 BTU down to 12,000 BTU, enough to heat the average bedroom or dining room.” He adds that if you had a 40,000 BTU fireplace and only needed to use 50 percent of its capacity, you’d pay less than $1 an hour to operate.
Do you need a fireplace to buy a house?
Fireplaces have always been among the top amenities for homeowners looking to buy a new house. In fact, they rank just second behind outdoor patios, decks and porches, according to the National Association of Home Builders ( NAHB ). While the cost of adding a fireplace to an existing home used to be prohibitively expensive—requiring the creation of an exterior stone chimney, flue, firebox and, in many cases, floor supports to accommodate the weight of the hearth—today’s options are not only affordable, but a relatively easy home improvement.
Do vents need to be inspected annually?
In addition, the HPBA recommends that all vents for vented gas fireplaces be inspected on an annual basis by a chimney sweep certified by the Chimney Safety Institute of America and also recommends the installation of a carbon monoxide detector with all hearth products. Advertisement.
Does a wood burning fireplace have a damper?
With wood, a certain amount of time is required to light the fire, turn that energy into heat and then get that heat into a room.”. Ruppa points out that in contrast to a gas fireplace, whose warmth is thermostatically controlled, a wood-burning unit comes with only an air control—the damper. That, he says “allows you to control the amount ...
Can you install a gas fireplace in direct contact with a combustible wall?
What has made them so is the technology and installation flexibility of gas-fueled models. Since no actual combustion occurs in gas fireplaces, zero-clearance installation is possible, which, according to Monessen Hearth Systems, means that “these fireplaces can be installed in direct contact with combustible walls and floors.
Is it expensive to add a fireplace to a house?
While the cost of adding a fireplace to an existing home used to be prohibitively expensive—requiring the creation of an exterior stone chimney, flue, firebox and, in many cases, floor supports to accommodate the weight of the hearth—today’s options are not only affordable, but a relatively easy home improvement.
How to mock up a fireplace?
Mock up the fireplace using the dimensions given in fireplace brochures and outline the hearth shape with masking tape. Your new fireplace will have a major impact on your room. Build a simple mock-up to get a feel for the amount of space it takes up and to see how the angled placement will affect furniture arrangement and traffic patterns.
How much does it cost to run a gas line to a fireplace?
Hire a plumber to run the gas line during the framing process and connect it to the fireplace ($250 to $500). In addition to a basic set of hand tools, you’ll need a circular saw and a drill. A power miter box is handy but not necessary for cutting the angles on the framing parts.
How much space between a fireplace and a wood frame?
Allow 1/2 in. of space between the wood framing and the fireplace on both sides.
Is gas fireplace better than wood?
But modern gas fireplace come pretty close, and without the draw backs of wood. Not only does gas burn much cleaner, making it a better choice for the environment, but there are no messy logs to carry through the house or ashes to clean out. And lighting the fire is as simple as flicking a switch or turning a valve.
Is a direct vent fireplace safe?
The fireplace we’re using, and the type we recommend, is a direct-vent fireplace. This type draws air from outdoors to feed the flame. Not only is this setup more efficient because you’re not losing valuable heated air up the chimney, it’s safer too because it greatly reduces the possibility of dangerous carbon monoxide backing up into your home.
Do gas fireplaces require electricity?
Most gas fireplaces don't require electricity to operate. However, if you ever decide to add a blower to increase heat output or a hand-held remote control, you'll have to connect the fireplace to an available electrical circuit, so run a wire to the fireplace while it's accessible.
Can a fireplace vent run through the roof?
Thanks to the ingenious two-layer design that keeps the outside of the pipe relatively cool, the vents from direct-vent fireplaces can run straight out through the wall or up through the roof, allowing great flexibility in design and placement of the fireplace. Even so, there are very specific requirements that your fireplace and vent installation must meet. Check the installation manual to make sure. Here are a few key points to look for:
How big of a brick do you need for a flueless gas fire?
Fitting a flueless gas fire requires that a 100cm 2 ventilation brick be fitted on an external wall in the room where the fire is fitted. Also, depending on the fire, the room must be a certain size, generally between a minimum of 25 – 30 cubic metres.
How efficient is a balanced flue gas fire?
Balanced flue gas fires are also very efficient with a heat efficiency rating of around 80 – 90%. They must be installed on an external wall though an additional air vent isn’t needed as they use a double exhaust pipe that draws fresh air in through the outer pipe and expels fumes through the inner pipe.
How long do flueless inset gas fires last?
They use a catalytic converter to clean the fumes; these catalytic converters are rated to last for 27 years.
Do fires require an electric supply?
Share image... The fire is similar to a standard open-fronted fire but has a pipe leading from the back of the fire which has a fan on the end. It’s worth not ing that these fires will require an electric supply. Most models do need installing on an external wall, with the pipe venting straight out the back.
Can a Verine fire be installed on an outside wall?
Most models do need installing on an external wall, with the pipe venting straight out the back. However, among the Verine Fires range there are fires that come with an optional flue extension kit allowing venting through a side wall; the flue can even be extended to go over a garage as shown in the image above.
How to get a propane fire burning?
To get your fire burning for the first time, you will need to ignite the pilot light, which can be left on even when you are not using your fire. Once lit, a propane gas fire works similar to a natural gas fire – you can control the heat by simply adjusting the control knob.
How long does it take to burn a gallon of gas in a 30,000 BTU fireplace?
So, if you had a 30,000 BTU fireplace, it would burn 1 gallon in about 3 hours.
How Does a Propane Gas Fireplace Work and How Do I Fit One?
A propane, or LPG, fireplace works slightly different to a natural gas fireplace .
How Big of a Propane Tank Do I Need for a Fireplace?
How much propane an LPG gas fire uses will depend on a few things, such as:
What are the advantages of using LPG?
So, what exactly are the benefits of using an LPG fire if you are in this situation? Here are just a few advantages to consider: 1 Gas is one of the cheapest fuels. Electricity can be costly when used as your main heating source. Oil can be cheaper, though gas can also be used to fuel other appliances too, like cooking hobs 2 Gas is also clean and efficient .While oil is a common choice for those living off-grid, it is highly polluting. Wood burning is another option, though you need to ensure you burn it correctly to limit air pollution – plus, it isn’t as convenient as gas. 3 Gas is easy to source. As we said above, wood burning is a good alternative, but you need to ensure you have a stable, good quality supply and somewhere dry to keep it.
What happens if you use the wrong gas?
If you use the wrong kind of gas, you could be creating a severe safety hazard. At Direct Fireplaces, you can filter all of our gas fireplaces by ‘Gas Option’, so you can easily find one that suits your needs.
Where to put LPG gas tank?
To do this, you will need to buy an LPG gas tank. These are usually placed outside the home, close to the wall where the appliance you would like to connect to is. If you want a large tank to fuel multiple appliances, these can be placed in the ground. Next, you will need to contact a Gas Safe engineer. They will make sure that the gas line ...
What is a B vent gas fireplace?
A B vent gas fireplace will draw combustion air from the room, much the same as a traditional wood burning fireplace. Exhaust gases are vented to the atmosphere via a two-ply galvanized vent pipe known as Type B venting. This is the same type of venting used for many gas furnaces and water heaters.
How does a B vent fireplace work?
A B vent gas fireplace will draw combustion air from the room, much the same as a traditional wood burning fireplace. Exhaust gases are vented to the atmosphere via a two-ply galvanized vent pipe known as Type B venting. This is the same type of venting used for many gas furnaces and water heaters. Because they are not efficient, B vent fireplaces are not as popular as they once were. Direct vent fireplaces will use a pane of tempered or ceramic glass to seal the combustion chamber from the room. To allow the fireplace to receive air for combustion, a double-walled vent pipe will be used. The inner tube will vent the exhaust to the atmosphere, while the outer tube will pull combustion air from outside. The outer tube will also help to keep the entire vent system cool by enshrouding the inner exhaust tube.
Why are B vents not as popular as they once were?
Because they are not efficient, B vent fireplaces are not as popular as they once were. Direct vent fireplaces will use a pane of tempered or ceramic glass to seal the combustion chamber from the room. To allow the fireplace to receive air for combustion, a double-walled vent pipe will be used.
What to know when purchasing a gas fireplace?
In the case of a gas fireplace installation, there is a long list of the different valve and burner systems to choose from. Among the choices in the gas fireplace category are millivolt and electronic gas valve systems. While they both perform the same basic task, they operate very differently. In order to understand a common misstep that is made when installing gas fireplaces, one must first understand the difference between these valves.
What trades are involved in fireplace installation?
The installation involves attributes from many trades, including electrical, plumbing, and framing. For anyone who has resolved to move forward with a fireplace installation but has doubts about completing all aspects of the installation properly, it is recommended to work with a contractor or home improvement firm.
Why insulate the outer walls of an exterior chase?
You are most certainly supposed to insulate the three outer walls of any exterior chase to prevent the issue that you are now having.
Is a fireplace part of a remodel?
As if often the case when adding a fireplace to a house, the appliance installation is part of a larger addition or remodel project. The decision to add a fireplace may have come while the project is well underway and as a result, structural modifications may need to be made to accommodate the vent pipe from a wood or gas burning fireplace.
What is a gas fire pit table?
A gas fire pit table is a propane or natural gas fueled fire table that acts as a focal point in your backyard or patio. What’s the difference between a fire pit table and a fire pit? Fire pit tables usually have a base and top design, while a fire pit may be a simple base or even an individual burner surrounded by pavers. However, the terms are quite often used interchangeably. With a burner cover, a gas fire pit table can act as an outdoor coffee table when burner is not in use.
What is an upscale fire table?
For shoppers prioritizing style and looks, an upscale fire table offers safe yet realistic flames that are cozy warm. With so many design options from rustic and modern farmhouse to classic contemporary and industrial, your unique fire pit table will bring your backyard to the next level too.
Can a gas fire pit table be used as a coffee table?
With a burner cover, a gas fire pit table can act as an outdoor coffee table when burner is not in use.
Can you put a gas fire pit table on a deck?
With the positive connect of the Crystal Fire® Plus burners, most of the connections are already made for even quicker installation. Gas fire pit tables can also be safely placed on a wood deck, concrete or paver patio, or other backyard area ...
