Asphalt, also known as blacktop, is a blend of dark pitch and sand or gravel. It costs $8.50 per square foot — $2040 for a single-car driveway and $3553 for a two-car sized drive — and is available in colors on the black-gray spectrum.
Full Answer
How much does it cost to Blacktop my driveway?
Asphalt Driveway Paving Cost Asphalt , also known as blacktop, is a blend of dark pitch and sand or gravel. It costs $8.50 per square foot — $2040 for a single-car driveway and $3553 for a two-car sized drive — and is available in colors on the black-gray spectrum.
How much does it cost make a driveway?
Gravel driveway cost. A gravel driveway costs $1 to $3 per square foot to install. A 12×25 (1-car) gravel driveway costs $300 to $900, and a 24×24 (2-car) driveway is $600 to $1,800.Costs depend on the size and depth, gravel type, soil conditions, labor, excavation, grading, permits, and optional grid stabilization.
How much does it cost to resurface a driveway?
Depending on the type of surface you’re working on, costs can go up or down. If you have a concrete driveway, you can have it resurfaced for around $3 to $5 per square foot. If it’s too damaged or crumbly to resurface, the cost of a new concrete driveway goes for around $2 to $15 per square foot on average.
How much is black top?
How Much Does It Cost To Blacktop A Driveway? The average cost of installing an asphalt driveway is approximately $4,500. This cost, however, varies depending on various factors such as location, depth of required material, quality of the material, as well as the size of the driveway. Let’s take a closer look at these factors.
How do you calculate the cost of an asphalt driveway?
For the simplest estimate, you can use this formula.Length x width=Square footage of the driveway.Driveway sq ft x $3= low end cost.Driveway sq ft x 7= high end cost.Driveway sq ft x $2= low end cost.Driveway sq ft x $4= high end cost.When to reseal your driveway:When to repave your driveway:
How much is a 700 ft driveway?
For a larger driveway or thicker base, the cost will be higher. For example, a driveway 15 feet wide by 700 feet long with a six inch base will need approximately 25 tons of gravel, at a material cost of about $700. With delivery, the total cost will be around $1000.
Which is cheaper a concrete or an asphalt driveway?
The cost of an asphalt driveway is typically cheaper than concrete, costing $2.00 – $4.00 per square foot. Asphalt prices tend to fluctuate with fluctuations in crude oil prices. In contrast, a concrete driveway costs between $4.00 – $6.00 per square foot for a standard installation.
How do you quote asphalt?
To find the amount of asphalt needed, multiply the cubic footage by 145 to find the total weight needed, then divide by 2,000.
Is asphalt the same as blacktop?
Blacktop is heated to approximately 150 degrees celsius, whereas asphalt is only heated to 120 degrees celsius. Asphalt is has a higher bitumen content and for that reason is less porous and more resilient to wear and tear from high traffic and thus is the preferred choice for major highways.
What is the cheapest type of driveway?
gravelAggregate, or gravel, is the cheapest and most durable of these four common driveway materials.
Can you blacktop over concrete?
Well, the answer is yes! It is safe to pave asphalt over concrete. Concrete is a great base material because it is stable and allows for excellent compaction of the asphalt above. In fact, many miles of concrete roads are paved over with asphalt every year.
What type of driveway lasts the longest?
ConcreteConcrete is the old standby for driveways. Most suburban homes opt for this material for two big reasons: Concrete is typically the longest-lasting driveway surface, and, if installed properly, it is practically maintenance-free.
How often should asphalt driveway be sealed?
every two to three yearsHOW OFTEN SHOULD YOU SEAL YOUR DRIVEWAY? Asphalt sealcoating is every two to three years depending on how much traffic your driveway gets or how constantly it is being exposed to the elements such as UV rays, snow and other chemicals.
How thick should a asphalt driveway be?
2 to 3 inchesResidential driveways typically use 2 to 3 inches of asphalt with 3 being suitable for occasional large trucks or heavy equipment. Underneath the asphalt you should have 6 to 8 inches of granular base aggregate.
How do I calculate my driveway?
Measure the length of your driveway in linear feet. Measure the width of your driveway in linear feet. Multiply the length x width to calculate the total square footage of your driveway.
What is the asphalt price index?
2022 State IndexesStateJanMarCalifornia$404.70$507.20Colorado$436.23$628.91Connecticut$512.50$578.00Delaware$545.00$605.0042 more rows
Cheapest Driveway Material?
Gravel is by far the cheapest driveway material and one of the longest-lasting materials with a lifespan of 100 years. It still needs regular maint...
How Long Does a Driveway Last?
Driveways typically last around 30 years total, but some need more maintenance than others. Asphalt and concrete driveways need maintenance every f...
How Much Value Does a New Driveway Add?
On average a new driveway can add between $5,000 to $7,000 in added home value. Of course, that value depends upon the size of your driveway.
Which is Cheaper? Concrete or Asphalt Driveway?
Asphalt runs slightly cheaper than concrete with an average square foot cost of $3 to $7 but it won’t last as long as concrete. A concrete driveway...
How Long to Wait Before Driving on New Driveway?
It’s typically recommended that you stay off a new asphalt driveway for 24 hours, longer if it’s humid out. If you have a concrete driveway, you’ll...
How Often Should You Seal a Driveway?
Professionals recommend resealing an asphalt driveway every three to five years but it could be sooner depending upon the state of your driveway. P...
How much does it cost to repair a blacktop driveway?
Over the 15–20 year life of a blacktop driveway, repairs and maintenance cost $800–$1000. Compared to gravel, however, asphalt is solid to walk on in any footwear, including high heels. Commercial blends may be coarse or smooth. Ultra-smooth surfaces are easier to repair and maintain, but rough finishes offer traction.
How much does it cost to pave a driveway?
Nationwide, paving a driveway costs between $2700 and $6500. Depending on the size of your driveway and choice of materials, you could pay as little as $1200 to $12,000 or more. The average homeowner spends $4000.
How long does a gravel driveway last?
With care, a gravel driveway can last 50 years or more before it needs a major overhaul. Gravel does have drawbacks. It’s not as hard or even as asphalt or concretion and can be a tripping hazard. It’s prone to ruts, and in cold climates, snow removal takes some of the gravel with it.
Why is my concrete driveway heaving?
The small spaces between each allow moisture to drain underneath, but in cold climates, the build-up of water and ice can cause heaving. Pros recommend using thicker, heavier slabs to keep the driveway stable. Drawbacks to concrete driveways include staining — a problem that regular cleaning solves — and cracking.
How much does asphalt cost?
It costs $8.50 per square foot — $2040 for a single-car driveway and $3553 for a two-car sized drive — and is available in colors on the black-gray spectrum. The cost of materials plus labor averages $3500—$4100.
Why do people put paved driveways on their homes?
A paved driveway makes your property more functional and attractive. It adds to its resale value and inspires pride. Whether you are planning to sell your home or intend to live in it for a lifetime, nothing says “welcome home” like a professionally paved driveway.
How much does concrete cost per square foot?
Concrete driveways costs slightly more than asphalt per square foot — $9.00 versus $8.50 — but it’s a favorite because it’s durable, attractive and relatively low-maintenance. Estimates for labor and materials average $3900–$6000 for a 240-square foot area.
How much does it cost to pave a road?
Cost to pave an asphalt road. The average cost to pave a private one-lane asphalt road is $35 to $85 per linear foot. Paving a two-lane (24'-wide) asphalt road costs $70 to $170 per linear foot or $370,000 to $900,000 per mile. Blacktop road construction costs more than driveways because roads need 5" to 11" thick asphalt.
How much does it cost to repave an asphalt driveway?
The average cost to repave an asphalt driveway is $4 to $10 per square foot with a new gravel base or $3 to $7 per square foot with an existing base. Repaving a 2-car (20’x20’) asphalt driveway costs $1,600 to $4,000 on average. Repaving includes removing and hauling away the existing asphalt.
How thick should a driveway be?
A new residential driveway needs 3 to 5 inches of asphalt over 4 to 8 inches of rock-base foundation to withstand temperature changes and last 20+ years. Some companies recommend a 2" thickness to save $0.50 to $1 per square foot, but won't provide a warranty due to deterioration risks.
How long does asphalt last?
An asphalt driveway lasts 15 to 30 years and requires sealcoating every 3 to 5 years. Boosts curb appeal and resale value. A new asphalt driveway needs an asphalt layer 3" to 5" thick to last. Resurfacing only the top layer or asphalt overlay costs $1 to $3 per square foot.
How much does stamped asphalt cost?
Colored or stamped asphalt costs $5 to $15 per square foot for a new driveway or replacement, or $3 to $8 per square foot for resurfacing the top layer. A 20x20 stamped asphalt driveway costs $2,400 to $6,000. Decorative patterns are sealcoated, which colors and protects the surface.
How much does it cost to lay asphalt over concrete?
Laying new asphalt over a concrete driveway costs $1 to $3 per square foot. Contractors fill cracks with concrete-repair caulk before paving. Resurfacing concrete with asphalt is cheaper than replacing concrete. However, special preparation is required to stabilize the concrete and prevent cracks.
How much does it cost to install asphalt curbs?
Asphalt curbing costs $3 to $6 per linear foot to install. Adding asphalt curbing to a 400-square-foot driveway costs $120 to $240. Repairing or replacing asphalt curbs costs $8 to $15 per linear foot on average. Total costs depend on curb thickness, styles, and labor.
How much does a paver driveway cost?
They offer a wide variety of designs, shapes, sizes, and colors. A paver driveway will cost between $13-15 per square foot. A poured concrete driveway ranges from $7-9 per sq ft.
What is the most expensive option to have a driveway removed?
Repaving. Repaving your driveway requires removing the old driveway completely. This is the most expensive option, because you will be paying to have the old driveway removed and a new driveway installed. This is of course the most expensive option, but a paved driveway has a lifespan.
What is resurfacing a driveway?
Resurfacing is the middle ground of driveway repair. It’s also known as asphalt overlay. In many cases, this can repair significant asphalt cracks. Existing asphalt is covered with a new layer of asphalt, in a process similar to the original driveway.
Why does asphalt crack?
Over time, the heat from the sun’s rays will begin to break down the materials in the asphalt and remove moisture. As the asphalt weakens due to the sun, cracks begin to form.
How long can you drive on a driveway after it's installed?
You won’t be able to drive on our driveway for 3-5 days after it’s installed. You’ll need to avoid parking on the driveway for the first 14 days, particularly in the hot part of the day.
What is the cheapest driveway?
A gravel driveway is the cheapest option if you need a new driveway, at $1-3 per sq ft. It matches with any style of home. Classic gray gravel is well suited to a winding country drive. White gravel provides a modern look.
How much does it cost to install asphalt?
Asphalt paving material usually costs $40-80 a ton. One ton will cover 30 to 80 square feet. A residential driveway averages 9-24 square feet. Other materials are needed for asphalt driveway installation as well, and will affect the final cost.
Compare Quotes From Top-rated Local Flooring Contractors
The average costs to pave a driveway range between $3 and $15 per square foot. The cost depends on materials, size of the driveway and installation requirements. Expensive materials can cost as much as $30 per square foot while cheaper materials are as low as $1 per square foot.
Driveway Cost Per Square Foot
The cost of driveway installations is typically determined by the driveway site’s square footage. While the material itself and the installation cost affect the price per square foot, the square footage of a driveway will sum the total cost of the project.
Driveway Cost By Material Type
Depending on the material, paving a driveway can cost anywhere from $1,500 to over $11,000. Concrete is a popular choice because of its durability and long-lasting nature. Other popular types of driveways include asphalt or blacktop, gravel, pavers and rubber.
Driveway Installation Cost
The total cost of driveway installation depends on the size of the driveway, site conditions and the material used. Labor can make up about half of the total price per square foot while the price for new material can make up the other half. Thickness can affect material cost, especially for concrete and asphalt.
Frequently Asked Questions
Gravel is the least costly material to pave a driveway. The price ranges from $1 to $3 per square foot. The average total cost is usually around $1,200, though this number may not account for the fact that gravel is usually used to pave much larger driveways as a cost-reduction solution.
How much does it cost to build a driveway?
The cost to build a driveway ranges from $600 to $18,000, depending on the material. The cheapest driveways cost $1 to $3 per square foot for gravel, while standard concrete and asphalt driveways cost $3 to $8 per square foot.
How much does it cost to install a concrete driveway?
Concrete driveway. Installing a concrete driveway costs $2,400 to $4,800 on average or $4 to $8 per square foot for plain gray concrete. Adding decorative colors, borders, stamped patterns, and finishes costs $8 to $18 per square foot. Concrete lasts 30 to 40 years and handles hot climates better than asphalt.
How long does a concrete driveway last?
Asphalt driveways last 15 to 30 years, and concrete driveways last 30 to 40 years on average, depending on the climate and usage. Brick and stone pavers last 25 to 50 years. A cobblestone or gravel driveway lasts up to 100 years if well-maintained.
What is the cheapest driveway material?
The cheapest driveway material is gravel at $1 to $3 per square foot using aggregate made of crushed shells, crushed concrete or asphalt, or pea gravel . Tar and chip seal driveways are the second cheapest at $2 to $5 per square foot.
How much does gravel cost?
Well-built gravel driveways require light raking and new gravel once or twice a year. Gravel prices range from $10 to $50 per ton, depending on the stone size and type.
How much does an exposed aggregate driveway cost?
Exposed aggregate or pebble finish driveways cost $5 to $11 per square foot or $3,000 to $6,600 on average. Exposed aggregate features stones mixed into concrete or seeded on the surface. Natural aggregates provide a textured, nonskid surface in various colors, including pastels, earth tones, and deep reds and blues.
How much does a chip seal driveway cost?
Chip seal driveways cost $1,200 to $3,000 or $2 to $5 per square foot. Chip seal, also called tar and chip, lasts 7 to 10 years. Tar and chip driveways have the durability of blacktop, come in various colors, and feature layers of stone aggregate spread over hot liquid asphalt.
How thick should a surface be for asphalt?
The thickness should be about two inches as it is considered a standard for asphalt overlays and surface courses. Two-inch thickness has the potential to properly bonds the surface course to the binder course. If the thickness is less than two-inch it will cause raveling, cracking, and other asphalt issues.
What is hot mix asphalt?
Hot Mix Asphalt: It is also known as the “Dense-Graded Mix”. This type of asphalt is considered ideal for surfacing and repairing needs. During its production, the binder will be heated at a very high temperature to reduce viscosity. The high temperature will also remove all moisture prior to mixing.
Is asphalt a liquid or semisolid?
Asphalt is a semi-solid form of petroleum and appears in a sticky, black, highly viscous liquid form. It is classified as a pitch and can be found in natural deposits as well as a refined product. If it has a mixture of 95 stone, sand, or gravel that bounds together by asphalt cement, then it will be known as hot mix asphalt. ...
How much does it cost to build an asphalt driveway?
An asphalt driveway typically costs about $2-$5 a square foot, $1,200 - $3,000 for a 12'x50' single-car driveway; or $25,000-$50,000 for up to a quarter mile. Slopes, curves, odd shapes and other complications add to the total cost, and smaller jobs aren't necessarily cheaper because it costs the contractor a minimum amount to haul ...
Who installs asphalt driveways?
Asphalt driveways are typically installed by asphalt or paving contractors (although general building or landscaping contractors may do this as part of a larger project, and sub out the asphalt work. The Better Business Bureau lists tips for selecting an asphalt driveway contractor [ 3] . Get several estimates;
Why is asphalt better than concrete?
Asphalt is a common driveway material because of its relatively low price compared to concrete. It generally works better and is more popular in colder climates because it can crack with constant exposure to high temperatures. CostHelper readers report paying $2,300-$10,300 to install a new asphalt driveway or completely remove replace an old one, ...
What should be included in asphalt?
It can include removing topsoil and organic material or existing pavement; compacting the soil; installing geo-tech fabric if the soil is weak or drains poorly; laying a base; and applying 2"-3" of asphalt and compacting it.
How long does it take for asphalt to cure?
Wait about 24-48 hours before driving or parking on fresh asphalt (or longer if the weather is hot). However, it can take up to 12 months for asphalt to completely harden and cure. An asphalt driveway can last 10-35 years, depending on the quality of the installation and maintenance.
Do I need a permit to build a driveway?
Because a driveway connects to a public street, there may be local regulations governing the width of the driveway and the materials used to build it. A permit is typically required, and fees vary from nominal to pricey, depending on location.