Here's the throttle body relearn procedure 1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds.
Full Answer
How to program a throttle position sensor?
Steps on How to Program a Throttle Position Sensor for a Throttle Valve Closed Position Learning. Step 1 Start by forming the throttle valve closed potion leaning. Step 2 Be sure that the accelerator pedal is totally freed or released Step 3 Then grab the keys and turn "ON" the ignition switch. Wait 10 seconds. Step 4
How to perform a throttle relearn test on a 2008 Chevy Silverado?
Here's the throttle body relearn procedure 1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds. 3) Start the engine again and let it idle in park for 3 minutes one more time. More ›.
What is the throttle body relearn procedure?
16/07/2014 · Performing a throttle relearn on GM throttle-by-wire vehicles can easily be done with the Mac Tools Mentor Touch Scout, No. ET6100. For example, to perform a throttle relearn on a 2008 Silverado 5.3L, select and run the Idle Learn Reset test. Then start the engine and allow the ECM time to begin to learn. Additionally, the Mentor Touch Scout supports Throttle Sweep and …
Why do I need a GM throttle body relearn?
And this should complete this reset programing. Next is on the Throttle Valve Closed Position Learning. Steps on How to Program a Throttle Position Sensor for a Throttle Valve Closed Position Learning. Step 1; Start by forming the throttle valve closed potion leaning. Step 2; Be sure that the accelerator pedal is totally freed or released. Step 3
How do you reset a GM throttle position sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do I relearn my throttle position sensor?
1:112:42When Should I Reprogram My Car's Throttle Body? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.28-Dec-2016
How do I reset my GM electronic throttle control manually?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.
How do I reset my Chevy throttle body?
Fully depress the accelerator pedal for 10 seconds. At this point the check engine light should change to blinking slowly indicating “Erasing ECU Memory”. 8. Release the accelerator pedal and turn the ignition switch to off.
How do you calibrate a throttle position sensor?
1:544:19How to replace / calibrate your throttle position sensor TPS (Honda)YouTubeStart of suggested clipEnd of suggested clipYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to theMoreYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to the negative lead of the battery. And the positive lead should be connected to the little red wire.
How do I reprogram my throttle body?
Leave the key off for a moment, turn the key to the "On" position again, wait 3 seconds, and press the accelerator 5 times in 5 seconds. Wait 7 seconds, and hold the accelerator down. The check engine light should start blinking, continue to hold pedal down until it stops blinking. You can then start the car.21-Mar-2017
How do I reset my throttle body after cleaning?
The idle will relearn if you put the vehicle in drive and allow the idle to come down with all accessories off for about two to three minutes. Then turn on your a/c with blower in high position for three minutes. This should fix it.18-Jan-2016
What happens when you unplug throttle position sensor?
The TPS as we call it is one of the most important sensors on the engine. Without it, the computer has no way of knowing when you push down on the gas or open the throttle. Best it can do it watch some other sensors and make some estimated guesses. On some cars, it may burp just as you unplug it if it's running.
How do you reset the ECM on a Chevy truck?
There's no complicated reset procedure; You just need to cut off power for a long enough time where the ECM forces a reset when it regains power once more.
How do I relearn idle?
0:403:27Idle Relearn Procedure After Battery Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat you have to do is circle. The key twice. Before so it's in the off position right you circleMoreWhat you have to do is circle. The key twice. Before so it's in the off position right you circle the key. Once twice and then you put your foot on the brake. And then you start the car.
What to do after cleaning a GM throttle body?
After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn. After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn.
Can you throttle relearn without a scan tool?
Throttle relearn can also be done without a scan tool, essentially by letting the vehicle idle in park for several minutes and allowing time for the ECM to learn. See appropriate service information for vehicle specific procedures and details if you wish to perform a throttle relearn in this way. Information provided by Mac Tools.
How to program a throttle in a car?
First step calibrating or programing your car throttle is to sit in your car and form the accelerator pedal released position learning. Do not depress the accelerator pedal when you turn the keys on wait for at least 2 seconds for each action. You need to know that the timing of this is important. So when you positioned yourself ready ...
How to program throttle position sensor?
Steps on How to Program a Throttle Position Sensor for a Throttle Valve Closed Position Learning. Step 1. Start by forming the throttle valve closed potion leaning. Step 2. Be sure that the accelerator pedal is totally freed or released. Step 3. Then grab the keys and turn “ON” the ignition switch. Wait 10 seconds.
How to release the accelerator pedal?
Step 1. Make that the accelerator pedal is completely released or free, then turn “ ON” ignition switch and wait for 3 seconds. Step 2. You want completely depress the accelerator pedal very hard and fully release the accelerator pedal as quickly as possible 5 times within 5 seconds.