Here's the throttle body relearn procedure 1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds.
How do you reset the throttle body on a Chevy?
Fully depress the accelerator pedal for 10 seconds. At this point the check engine light should change to blinking slowly indicating “Erasing ECU Memory”. 8. Release the accelerator pedal and turn the ignition switch to off.
How do I relearn my electronic throttle body?
1:112:42When Should I Reprogram My Car's Throttle Body? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
How do I reset my GM electronic throttle control manually?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.
How do you calibrate a throttle body?
0:093:26Throttle Calibration- Relearn? Car Feels Different - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut your car in the run. Position. Once everything is good press down on the gas. And hold it downMorePut your car in the run. Position. Once everything is good press down on the gas. And hold it down for 20 seconds slowly let off the gas. Okay then put the car in the off.
How do you reset the throttle body sensor on a Chevy Silverado?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do you reprogram a throttle position sensor?
How to Reset Throttle Position SensorPut the key in the ignition.Turn the key to the On position, without cranking the engine. Wait a few seconds, then turn it off.Repeat the second step.Crank the engine.Pull the parking brake.Set the gear lever in Drive.Wait 5-10 minutes.02-Jun-2021
How do you reset the ECM on a Chevy truck?
There's no complicated reset procedure; You just need to cut off power for a long enough time where the ECM forces a reset when it regains power once more.
How do you reset the throttle body on a 2011 Chevy Silverado?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutesMoreNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutes again after the 3 minute runtime the engine should be idling normally.
How do you adjust the throttle position sensor on a Chevy?
0:573:47TPS or Throttle Position Sensor Adjustment 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idleMoreBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idle speed. And then readjusting the TPS. The desired idle condition can always be met by the engine.
What happens if TPS is not calibrated?
If your TPS is faulty or uncalibrated, the sensor will be unable to accurately determine the position of the sensor. This will lead to a variety of symptoms, all of which are caused by the fact that the ECM is delivering the wrong air/fuel ratio to the cylinders thanks to the bad sensor.29-Oct-2021
Can a throttle body be adjusted?
For those customers who want even better performance the throttle body the throttle position sensor (TPS) can be adjusted.
What to do after cleaning a GM throttle body?
After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn. After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn.
Can you throttle relearn without a scan tool?
Throttle relearn can also be done without a scan tool, essentially by letting the vehicle idle in park for several minutes and allowing time for the ECM to learn. See appropriate service information for vehicle specific procedures and details if you wish to perform a throttle relearn in this way. Information provided by Mac Tools.
Recommended Services
On this particular re-learn, the scan tool is helpful because it can re-set learned airflow values to zero. However, as you can see from the Factory Service Manual instructions, merely driving the car after an unsuccessful "re-learn" will cause the new throttle body to learn the correct idle speed.
What others are asking
There is nothing that an owner of a 2009 Chevy Traverse, or most GM vehicles from 2007 thru 2011 that are equipped with this design power steering pumps/Rack and Pinions, can do to prevent these failures. Chevrolet has known about...
What happens if you don't take the throttle off?
Or, if you didn't take it off and instead moved the throttle plate, you could have damaged the little gears that control the throttle plate. You're not supposed to move the throttle plate "manually" on a drive-by-wire throttle body.... Some people do it and get away with it, but you're really not supposed to.
Can you clean a throttle body with the gas pedal?
If you need to open the throttle plate a little to get the throttle body 100% clean, you can do so with the gas pedal. When I cleaned my throttle body, I left it connected electronically and cleaned it "under the hood".