remote start problem
- The remote start system is disabled through the DIC.
- The vehicle’s key is in the ignition.
- The vehicle’s hood is open.
- The hazard warning flashers are on.
- The check engine light is on. See Malfunction Indicator Lamp on page 3-38.
- The engine coolant temperature is too high.
- The oil pressure is low.
- Two remote vehicle starts, or one start with a time
Full Answer
What are the disadvantages of remote car start?
Nov 28, 2019 · I show you what could be the problem with your Chevy Malibu if your factory install remote start is not working.Get a cheap scan tool like mine: https://amzn...
What would cause a remote starter to stop working?
Sep 23, 2021 · For safety and security reasons, the remote engine start system on Chevy Silverado 1500 will prevent starting or stop the engine if running when one or more of the following conditions are met: The total run-time has exceeded 30 minutes. The coolant temperature gets too high. The oil pressure gets low. The security alarm is triggered.
Why is my remote start not working?
Dec 13, 2019 · 1) the remote start was working fine until you reset the car battery 2) there isn't a MIL/Check Engine light on 3) the remote is working fine for unlocking/locking the doors and trunk 4) All other electrical functions of the vehicle are working 100% there are 3 possibilities: 1) There is a wiring issue 2) Your BCM is malfunctioning
What can cause the remote start to stop working?
Mar 06, 2020 · The vehicle cannot be remote started if: . The RKE transmitter is inside the vehicle or if the key is in the ignition. . The hood is not closed. . There is an emission control system malfunction and the lamp is on. . The ignition is in any mode other than off. . The hazard warning flashers are on. .
What causes a remote start not to work?
Reasons Your Remote Start is Not Working: Too Many Remote Start Attempts. Coolant and Oil Pressure. Unlatched Hood. Hazard Warning Lights.24-Jan-2014
How do you reset the remote start on a Chevy Silverado?
On your Chevy key fob, press and hold the “Unlock” and “Lock” buttons simultaneously until you hear the door locks engage and disengage again, indicating that you have successfully programmed your key fob. Re-insert the newly programmed key into the ignition in the “On” position to end the programming sequence.
How do I reset my remote starter?
Press the Lock button on your remote car starter. Within five seconds of turning it on, turn your key back to the "off" position (or press the start button again). Repeat the on-off cycle three more times—you'll do four in total.14-May-2020
How can you tell if a remote starter is bad?
3 Signs Of a Bad Remote StarterClicking the Key Fob Once or Twice Does Not Work. When you first get your key fob, ideally it should work flawlessly. ... Self-start a New Thing? Let's say you don't have problems starting your vehicle. ... Distance You Can Use the Starter Has Decreased.20-Jul-2018
Why does my remote start turn off after a few seconds?
The most common reason for a vehicle to start, then immediately shut off is engine checking. Compustar and Arctic Start systems monitor voltage or tachometer signals from your vehicle to know exactly when the vehicle has started.25-Jan-2020
Does a remote start drain the battery?
All remote starters, whether from Compustar, Arctic Start, or another brand, draw power from your battery. Even while your engine is off, a remote start system still draws current while it waits to receive a command from your remote fob.28-Jan-2020
How long does a remote car starter last?
Any vehicle started with the remote engine starter can idle for a total of 20 minutes. Automatic engine shutdown occurs after 10 minutes, but the vehicle may be remotely started as many times as you wish for an additional 10 minutes.
Help! My Remote Car Starter Doesn’T Work!
Enormis Mobile Specialties in Erie, Pennsylvania, has been specializing in remote starters since our inception in 1999. Over the years, Enormis has...
Hood Pin Switches Or Sensors
The single biggest thing that can cause a remote starter not to engage is a faulty or missing hood switch. This device gets installed under the hoo...
Batteries in Your Remote Control
Yes, believe it or not, that remote control on your keychain does take batteries and, after a period of time, they are going to get weak (diminishi...
Remote Starter Switch Is Off
Certain brands of remote starters come with a switch that is designed to temporarily disable the remote starter. The switch may be under your dash...
Remote start procedure for Silverado
You can remotely start your Chevy Silverado 1500 by following these simple steps:
Extend engine running time
When you remotely start the engine of your Chevy Silverado 1500, it will run for 15 minutes and then shut off automatically. You can perform another remote start procedure by pressing the LOCK button and then holding the REMOTE START button for four seconds on the key fob, which will run the engine for another 15 minutes.
Climate control
The climate control system on your Chevy Silverado 1500 will come on when the vehicle is started remotely, depending on the outside temperature. The rear defog and heated and ventilated seats, if equipped, may also come on.
Heated and Ventilated Seats
During a remote start, the heated or ventilated seats, if equipped, can be turned on automatically on your Silverado. When it is cold outside, the heated seats turn on, and when it is hot outside the ventilated seats turn on.
Enable or disable heated seats
If equipped and turned on, this feature will turn on the heated seats in your Silverado when using remote start on cold days.
Enable or disable ventilated seats
If equipped and turned on, this feature will turn on the ventilated seats on your Silverado when using remote start on warm days.
Steering column lock during remote start
It is normal for Silverado’s steering column to be locked during a remote start, but the column should unlock after the brake pedal is pressed and the vehicle is started.
dan.hill
I'm having a strange, random issue with my remote start and I'm curious if it's been happening to anyone else. Started when I tried to start the truck ('19 AT4 6.2L) with the onstar app. It failed, said not to try again and to start truck normally with start button. Did so, and the CEL was on.
dan.hill
That's disappointing. I tried searching on here and google, but wasn't coming up with much.
Booger T
I use mine all the time and have never had an issue. The advantage using the app over the fob is that you can remote start from anywhere, very handy if your not close enough to vehicle for fob to work.
aseibel
I have a K2, but use the same app as you. I don't think the issue is with the app, but rather some electrical gremlin in the truck. You said it has also occurred when using the fob.
dan.hill
You may be on to something. It does happen with the app or the fob. The issues started not long after I had 3 recalls done. One of the recalls was for a potentially loose ground cable I think. I'll mention that at the dealership this afternoon. Quote
dan.hill
Looks like it was a bad knock sensor causing the CEL and preventing the remote start. Dealer replaced it and it has been working fine. Hopefully that is the end of it.
redwngr
The vehicle cannot be remote started if: . The RKE transmitter is inside the vehicle or if the key is in the ignition. . The hood is not closed. . There is an emission control system malfunction and the lamp is on. . The ignition is in any mode other than off. . The hazard warning flashers are on. .
How to test remote start?
To test your remote start, put the key in the ignition and start the truck. Turn it off, get out of the truck and press your power lock switch on the remote.
How long does a remote start last?
Your remote start will only run for 10 minutes at a time. You may remotely start it again or continue the cycle by pressing the remote start button again while it is running. This will add another 10 minutes. So if you had it remotely started and it ran for 6 minutes before you hit the remote start again, it would run for a total of 16 minutes.
How long does it take for a Ford truck to start with a remote?
Press it again to sound the horn. Now press your remote start button on the remote. It should start. You may have to hold the remote start button for up to 5 seconds. If this procedure doesn't work, then you need to have the truck checked out. Your remote start will only run for 10 minutes at a time.