There are two good approaches for widening: Starting with a straight bed trailer, weld outriggers to the existing frame. Usually these go in front of and behind the trailer tires. While this approach does not change the axle or side to side wheel spacing, it does include a change in wheel wells.
How can I widen my trailer?
There are two good approaches for widening: Starting with a straight bed trailer, weld outriggers to the existing frame. Usually these go in front of and behind the trailer tires.
Can you make a trailer wider than the width of tires?
In general, avoid making a trailer wider than the width of the tires. In other words, don’t make the outriggers or resulting deck go out beyond the tires. From a stability standpoint, and from a frame stress standpoint, it’s just not the best idea.
Why stub axles for Tubetube axles?
Tube axles are made with only enough stub axle inserted into the tube to stop the 'U'bolts crushing the tube. Making the stubs a neat fit will go a long way to ensuring the correct wheel alignment when finished. Too many projects, so little time, even less money!
Can axles be hollow all the way through?
There is no reason why the axle can't be hollow most of the way through. Tube axles are made with only enough stub axle inserted into the tube to stop the 'U'bolts crushing the tube. Making the stubs a neat fit will go a long way to ensuring the correct wheel alignment when finished.
How do you widen a utility trailer axle?
If the entire trailer needs to be wider, simply split the trailer down the middle (front to back). Cut all the cross members and add middle sections. Of course, this will also require a new axle because the spring seat distance and track width must get wider.
How do I extend my axle?
0:231:06Installing Axle Extenders - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff exposing the axle thread with the nut removed. And the washer from the kit install the washerMoreOff exposing the axle thread with the nut removed. And the washer from the kit install the washer onto the axle. The axle extender. Now the bracket will slide over the axle extension.
Can you upgrade axles on a trailer?
It's definitely possible to upgrade a trailer's axle rating to a higher rating by just swapping the axles. To pick out the correct axle you'll need to measure the distance between the hub faces and the spring seat centers and you'll know which will fit as a replacement.
Can you widen a torsion axle?
No, you cannot. In fact you can't even weld on them or the rubber melts, burns or just plain turns to charcoal. I'd never have another trailer with torsion axles myself, you're just limited too much with modifications down the road.
How do you attach an axle to a cart?
1:173:57Kar - a Simple to make DIY cart Axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo just drag it in like this then all you need is to have a drill. To have a drill and drill a holeMoreSo just drag it in like this then all you need is to have a drill. To have a drill and drill a hole hole right through through the tube and through the treaty axle and through the bolt.
What does axle set mean on JLG Lift?
0:141:01JLG Ultraboom Oscillating Axle System - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe oscillating axle system allows all four wheels to remain on the ground while traveling overMoreThe oscillating axle system allows all four wheels to remain on the ground while traveling over rough terrain.
How can I increase my trailer load capacity?
Since capacity is the axle(s) combined load rating, you will you need an axle upgrade to truly increase trailer load capacity. So, ditch the wimpy one, and buy another that meets your new load requirement. Sometimes that also means removing the spring hangers and replacing them with stronger ones.
How much weight can a 6 lug axle carry?
Most boxed/flatbed trailers equipped with a six-lug axle and a 15-inch wheel/tire combo are rated at between 3,500 and 6,000 pounds per axle, so that is 7,000 to 12,000 total pounds of load hauling ability, including the weight of the trailer.
How much weight can a 5 lug axle carry?
5 lugs sounds like the max each axle may be rated for is 3500 lbs.
Can I weld on a torsion axle?
Expert Reply: Torsion axles use internal rubber cords that make it tricky to weld them, such as for installation of a brake flange to let you install electric drum brakes on the axle.
Are torsion axles adjustable?
Torsion axles have a straightforward, attached construction with adjustable ride height and a rubberized suspension system.
What's inside a torsion axle?
Torsion axles are made up of thick rubber cords concealed in the axle's tubing. As each wheel moves up and down, the rubber cords compress offering an even wheel suspension for a smooth ride. Each wheel acts independently, moving and absorbing shocks.
Step 1: Removing the Original Axle
this step is hard for me to explain because not all axles are the same. i just had to undo two bolts to get my front axle off, but that doesn't mean that you will have to. so here are the removal instructions for my axle, but these probably wont help you when it comes to your's.
Step 2: Adding a New Axle
for this step you will need to have a large peice of steel scafold tubing, which is about a metre long. you should grind off about 5 inches either side of it to allow you to weld on the wheels later. now find the middle of the tubing and place onto the go kart.
Step 3: Welding on the Wheels
now we come to the hard part of the build, attaching the wheels so that they are the right orientation. this took me about ten minutes of tweeking and adjusting to get ready for welding. first you will have the remains of the origonal axle left attached to the wheels.
Step 4: Attaching the Track Rod Arms
these are just the bits that turn the wheels round when you turn the steering wheel. you need to cut each one in half and extend them with a peice of 1 inch tubing.
Step 5: Painting
first you will have to get all of the rust/existing paint off. this may take a while depending on whether you use a wire brush or a grinder. i used a grinder, so it only took me a couple of minutes. next paint the axle in primer. i used zinc 182 primer, but you can use whatever is available to you.