Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Set the blade depth so you won't cut into the house sheathing below the siding.
Can you put a ledger Board on top of vinyl siding?
Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location.
Do I need a ledger Board on my house wall?
If your house was built since the mid 1990s, there is a chance that the floor system is constructed with a MWJ (Manufactured Wood Joist) floor system. In these cases, it is very important to consult with a building inspector, engineer or architect to understand how to correctly attach a ledger board to the house wall.
How do you remove a ledger board from aluminum siding?
Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Set the blade depth so you won't cut into the house sheathing below the siding.
How do you install a ledger board?
Cut the boards to the desired lengths. Make sure the crown (the upward curvature of the growth rings) of the ledger board points up. Hold the ledger in place with nails.
How do you attach a ledger board to lap siding?
Attach-A-Deck works great for mounting a ledger over existing siding. You just drill 2 1/2 in. holes through the siding to the face of the sheathing, apply the Attach-A-Deck fasteners and mount the ledger to the house.
How do you attach a ledger board to the side of a house?
0:492:19Before installing the ledger board into place there's one very important step which is to waterproofMoreBefore installing the ledger board into place there's one very important step which is to waterproof the houses rim joist using a rubber membrane. This will keep any water running down the exterior.
How do you frame against siding?
0:020:55Do not apply vinyl siding directly to studs or furring strips. When preparing a masonry wall firstMoreDo not apply vinyl siding directly to studs or furring strips. When preparing a masonry wall first apply vertical furring strips on 16 inch centers. Then apply the substrate to the furring.
How do you flash a deck against siding?
1:343:23Again with state line now I'm going to go ahead and show you a proper way to flash attack. We haveMoreAgain with state line now I'm going to go ahead and show you a proper way to flash attack. We have one layer two layer three layers. The borrow fourth layer is the very top piece and the siding will
What do you put behind a ledger board?
7:3312:31The risk is if you don't do a good flashing job that we end up getting water that back behind theMoreThe risk is if you don't do a good flashing job that we end up getting water that back behind the ledger board. Now of course we pre flashed it with that first piece of peel-and-stick.
How much weight can a ledger board hold?
The ledger is 10' long so every foot of ledger must be designed to carry at least 200 lbs of load.
What goes between frame and siding?
Underlayment Underlayment or weather resistive barrier (WRB) is installed between the siding and the sheathing. This can be tar paper or a house wrap such as HardieWrap® or Tyvek HomeWrap®.
How do you close the gap between siding and foundation?
Use duct tape and place it at the top portion of the siding strip, spanning until you get to the lowest part. Close the gap with a caulk gun, sealing between all the strips. Let the caulking dry before removing the duct tape, then repeat the process on the other strips.
What do you put between siding and ground?
Fiber cement should be kept at least 6 inches above the ground. It's recommended to keep the bottom edge of the first course even with the bottom edge of the trim. The most popular brand of fiber cement is James Hardie. In fact, the name is practically synonymous with the siding material.
How far should deck boards be from siding?
about 1/8"The first board you install should be about 1/8" (3.5mm) away from the siding, to account for drainage, expansion and contraction. Predrilling is typically necessary when fastening any type of hardwood decking.
How do you attach a deck ledger to a house?
2:155:25One with the leg bolts all in place i'll just snug them. Up. Here's the second fastener that we'reMoreOne with the leg bolts all in place i'll just snug them. Up. Here's the second fastener that we're going to use and we're going to use it to fasten the ledger to the foundation.
Does a ledger board need flashing?
1:3111:23This is flashing here so this would be installed. Next this would be both below the ledger board.MoreThis is flashing here so this would be installed. Next this would be both below the ledger board. And the membrane would be installed this way on top of the top edge of the flashing. And then the
How do you attach a ledger to a house?
0:472:03On both sides but the X is usually where the joints go. Now we can put our leg bolts. In. I like toMoreOn both sides but the X is usually where the joints go. Now we can put our leg bolts. In. I like to go in between each joist every 16 high/low. There you go now it's nice and secure against the house.
How do you attach a deck to the side of a house?
2:155:25One with the leg bolts all in place i'll just snug them. Up. Here's the second fastener that we'reMoreOne with the leg bolts all in place i'll just snug them. Up. Here's the second fastener that we're going to use and we're going to use it to fasten the ledger to the foundation.
How do you attach a roof ledger to a house?
A ledger should be affixed to strong parts of the house's framing, such as second-floor joists or wall studs. The strongest ledger connection relies on bolts that run through the ledger and the house sheathing and rim or band joist and then are fastened with nuts and washers affixed from the other side.
Can I attach a ledger board to wall studs?
Mike Guertin (on Instagram @mike_guertin), a builder and remodeler in East Greenwich, R.I., and a presenter at JLC Live, responds: Yes, it's technically possible to fasten a deck ledger to the narrow faces of 2-by studs rather than to a solid rim joist.