Spray the dent on your motorcycle gas tank and a one-inch area surrounding it with liquid carbon dioxide for 30 seconds. Wait two minutes while the difference in temperature between the heated dent and the liquid carbon dioxide cause the dent to pop out of your motorcycle's gas tank, leaving the surface perfectly smooth
Can you get a dent out of a motorcycle gas tank?
I have restored over a dozen motorcycles and repainted every single one of those gas tanks which included dent repair. I have used every method imaginable to get dents out. This article will describe the best way and exactly how to get them out so you’re not embarrassed to take your motorcycle for a ride.
Is it common to have dents on the gas tank?
Nowadays, almost every rider may face a dent issue in his motorcycle. But many people don’t know the right ways to solve this problem properly. However, if you like them, keep reading this article. Here I am going to show how you can easily get rid of this problem without removing the paint. It is common to have dents on the gas tank.
How to remove a fuel tank from a motorcycle?
First of all, you need to extract the fuel tank from the motorcycle body. But be careful when you remove the tank. It may damage your fuel system or other internal parts. However, don’t repair or complete the dent removal action keeping the gas tank in the motorcycle.
How do you fix a dented gas tank?
It’s the easiest way of fixing the issue at home and without too much hassle. However, this depends on the actual dent since some might be too big than a can of compressed air can fix. If you’d prefer something else, consider using heat to warm up the tank, making the metal it’s made with a bit easier to work with.
How to clean carbon dioxide from motorcycle gas tank?
How to fix a dent in a motorcycle gas tank?
What happens if you spray compressed air upside down?
How to get rid of a dent in a hair dryer?
How long does it take for a dent to pop out of a motorcycle?
See more
About this website
How much does it cost to get a dent out of a motorcycle gas tank?
Different shops charge different amounts, depending on what type of motorcycle you have. However, you can generally expect to pay anywhere between $200-$300 for a gas tank dent repair.
How do you get a dent out of an aluminum motorcycle gas tank?
0:206:54How to Remove Dents from a Motorcycle Tank | Complete GuideYouTubeStart of suggested clipEnd of suggested clipYou want to gently press down on to the dent. And hold it there for about five to 10 seconds. You'reMoreYou want to gently press down on to the dent. And hold it there for about five to 10 seconds. You're then going to let it sit for about five minutes.
How do you fix a dent on a Harley Davidson gas tank?
1:194:57Harley Davidson Sportster Gas Tank Paintless Dent Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd we're using slow pressure to the back side of the metal. Slowly shaping it back out and usingMoreAnd we're using slow pressure to the back side of the metal. Slowly shaping it back out and using that light as a reflection. We're also using a heat gun because of how deep.
How do you Undent a gas tank?
1:095:23how to remove dents from motorcycle gas tank dent fix how to ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I use the edge of the pipe as a lever I clamp onto the pin. And then I pull down on this end ofMoreAnd I use the edge of the pipe as a lever I clamp onto the pin. And then I pull down on this end of the vise grip which pops the little ding straight out of the tank.
How do I fix a hole in my motorcycle gas tank?
0:223:14How To Solder Holes In Motorcycle Gas Tanks (2019) - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike I said you'll need a strong soldering iron some flux of some kind I prefer the liquid kind butMoreLike I said you'll need a strong soldering iron some flux of some kind I prefer the liquid kind but this paste is all I had on hand and of course you'll need some solder.
How do you get dents out of aluminum?
0:412:23Paintless Dent Repair Aluminum F150 - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne technique we use is heating the panel. And a lot of times we still do this with steel. ButMoreOne technique we use is heating the panel. And a lot of times we still do this with steel. But definitely with aluminum we try to get it between 100 to 125 degrees.
How do you Bondo a motorcycle gas tank?
0:2112:08Repairing a dent in a motorcycle tank - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou know I probably feel a can fill up dents quite large like this but whoever's done this hasn'tMoreYou know I probably feel a can fill up dents quite large like this but whoever's done this hasn't prepared the metal properly. So today I'm going to rip out that body filler put in a new body filler.
How do you fix a rusty motorcycle gas tank?
4:3716:34How To Remove Rust From A Motorcycle Gas Tank - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith about two tablespoons of motor oil. And i'm going to put that in here. And swish that allMoreWith about two tablespoons of motor oil. And i'm going to put that in here. And swish that all around because what happens is this acid will take off the rust.
How do you remove the gas tank on a Harley Davidson Softail?
2:1414:33How To Remove @Harley-Davidson Softail Fuel Tank With A Cross Over ...YouTubeStart of suggested clipEnd of suggested clipBut you can actually push the back of that tank up because your hose is in the front. And your tankMoreBut you can actually push the back of that tank up because your hose is in the front. And your tank is declined like this so we've got some fuel back here that's not going to be getting up to. This.
What is pops a dent?
0:222:23Does It Really Work: Pops-A-Dent - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is pop sedan and the maker claims this kit will easily remove dents and dings from your vehicleMoreThis is pop sedan and the maker claims this kit will easily remove dents and dings from your vehicle caused by hail other car doors shopping carts and more the key the unique bridge adhesive.
Best Motorcycle Gas Tank Dent Removal Tool 2022 - Top 10 Rated
This is a buying guide made with you in mind. It is a buying guide created with a uniquely designed set of algorithms, to enable us to provide you with a list of the top 10 Motorcycle Gas Tank Dent Removal Tool that are currently available in the marketplace.
Clogged gas tank, old lining is peeling off. How to get it out?
I had Kreem do this in my old SR500, with the tank rusting again. I was able to get ahold of some of it with pliers and pull it out. From there, I took the tank to a radiator/fuel tank repair shop that "boiled out" the tank and recoated it with the RedKote hard shell liner they use, along with soldering up some holes.
How to get dust off a tank after sanding?
When it dries, you can use Bondo or whatever body filler you decide on and start filling in the dent using the scraper.
How to repair a dent in a motorcycle tank?
It’s important to remember that no matter how you attempt to repair a dent in a tank, you will need to completely remove the tank from the motorcycle and empty the gas inside. Once you drain the gas, poor some rubbing alcohol inside the tank and keep the cap open to let the residual gas evaporate. Rubbing alcohol is soluble with gasoline so it will ...
How much does it cost to paint a motorcycle gas tank?
The cost for a new motorcycle gas tank is usually around $150 -$200. You can get one for about $100 that is down to bare metal that you’ll need to paint yourself. Repairing and painting a tank yourself has proven to work well, even with amateurs who are willing to learn a new skill.
How to sand down body filler?
Wait for the body filler to dry according to the directions. Sanding it too early could mean sanding off big clumps at a time. Use the sanding block (not your hands) to sand down the body filler until it’s smooth. Start with the 80 grit sand paper and work your way up to using 400 grit.
Can you primer a tank in one go?
Remember to do several coats and to not attempt to coat the entire tank with primer in one go. If needed, practice on a piece of cardboard or other disposable material. Inspect the tank after the primer has dried.
Is it stressful to buy a motorcycle?
Looking into buying a motorcycle can be exciting, but it can also be a bit stressful if you don't know exactly what to look for especially when it comes looking for potential issues. I've been there...
Do you need to clear coat a gas tank?
Once that is dry, you’ll need to clear coat the entire tank. This ensures that gasoline or other chemicals don’t eat through the paint. Click here to see the clear coat I recommend in my list of suggested upgrades. Be sure to wear your respirator during this step because clear coat is especially potent.
How to clean carbon dioxide from motorcycle gas tank?
Use your damp polishing cloth to clean off any remaining liquid carbon dioxide from your motorcycle's gas tank. If the dent does not pop out of your motorcycle's gas tank on the first try, repeat the process. Empty your motorcycle's gas tank before attempting this procedure, and be sure that the gas cap is securely fastened.
How to fix a dent in a motorcycle gas tank?
Step 1. Park your motorcycle close enough to an electrical outlet so that the hair dryer cord will easily reach the dent on the motorcycle's gas tank. Plug the hair dryer into the outlet and set it down by the bike. Take the top off of the container of compressed air and put it within arm's reach of where you will be working.
What happens if you spray compressed air upside down?
Spraying a can of compressed air upside down causes it to release liquid carbon dioxide instead of compressed air. Spray the dent on your motorcycle gas tank and a one-inch area surrounding it with liquid carbon dioxide for 30 seconds.
How to get rid of a dent in a hair dryer?
Set the cloth aside on a clean surface. Pick up the hair dryer, positioning it so that the nozzle is pointed at the dent with an inch between the nozzle and the dent. Turn the hair dryer on "high.". Move the hair dryer back and forth over the dent for one minute, heating the dent and a one-inch area surrounding it.
How long does it take for a dent to pop out of a motorcycle?
Wait two minutes while the difference in temperature between the heated dent and the liquid carbon dioxide cause the dent to pop out of your motorcycle's gas tank, leaving the surface perfectly smooth
Options to Repair a Dented Gas Tank
You’ve got a few options when it comes to repairing any dents in your tank, these include:
Motorcycle Gas Tank Dent Repair Cost
The total cost of repairing dents in your gas tank will vary depending on which method you go with.
How to clean carbon dioxide from motorcycle gas tank?
Use your damp polishing cloth to clean off any remaining liquid carbon dioxide from your motorcycle's gas tank. If the dent does not pop out of your motorcycle's gas tank on the first try, repeat the process. Empty your motorcycle's gas tank before attempting this procedure, and be sure that the gas cap is securely fastened.
How to fix a dent in a motorcycle gas tank?
Step 1. Park your motorcycle close enough to an electrical outlet so that the hair dryer cord will easily reach the dent on the motorcycle's gas tank. Plug the hair dryer into the outlet and set it down by the bike. Take the top off of the container of compressed air and put it within arm's reach of where you will be working.
What happens if you spray compressed air upside down?
Spraying a can of compressed air upside down causes it to release liquid carbon dioxide instead of compressed air. Spray the dent on your motorcycle gas tank and a one-inch area surrounding it with liquid carbon dioxide for 30 seconds.
How to get rid of a dent in a hair dryer?
Set the cloth aside on a clean surface. Pick up the hair dryer, positioning it so that the nozzle is pointed at the dent with an inch between the nozzle and the dent. Turn the hair dryer on "high.". Move the hair dryer back and forth over the dent for one minute, heating the dent and a one-inch area surrounding it.
How long does it take for a dent to pop out of a motorcycle?
Wait two minutes while the difference in temperature between the heated dent and the liquid carbon dioxide cause the dent to pop out of your motorcycle's gas tank, leaving the surface perfectly smooth
