What kind of Paint can I use on cast iron?
- Hammerite REG500 500ml Radiator Paint – Gloss White.
- Hammerite 5084917 500ml Radiator Paint – Satin White.
- Rustins RADS250 250ml Quick Dry Radiator Paint Satin.
- Dulux Quick Dry Gloss Paint For Wood And Metal – Pure Brilliant White.
- Hammerite 400ml Radiator Enamel Aerosol – Satin White.
How to tell if bathtub is cast iron or steel?
- cast iron lavatory sink
- bathtub cast or metal
- Cast Iron shower pipe repair
- Cast Iron Pipe
- Your Favorite Kitchen Sink
How to cut a cast iron bathtub?
How to Cut a Cast Iron Bathtub
- Open a large drop cloth over the floor area to protect it. Turn the cast iron tub onto its side or on its back.
- Mark the areas of the cast iron tub that you wish to cut down, using a dry erase marker. ...
- Install a diamond-tipped blade into a standard circular saw, and plug in the saw's electrical cord.
How do you paint a bathtub?
Tips for painting a bathtub:
- Make sure your bathroom is well ventilated. ...
- You can use either a paint roller, paint brush or paint sprayer for painting a bathtub. ...
- The bathtub paint is a lot thinner than most paints. ...
- If the paint runs, smooth it out as soon as you can because it seems to dry faster than normal paint.
Can you paint over cast iron tub?
Painting over a cast iron tub can give new life and style to any bathroom. Whether the bathtub is rusted and peeling or simply in need of a refresh, it's important to plan each step in the process.
Can you paint the outside of a bathtub?
Yes, bathtubs can be painted with a near-new finish with a little elbow grease. You just need to make sure you have the right equipment and tools such as an epoxy primer and resin finish. Are there bathtub painting kits? There are a lot of DIY bathtub painting kits available.
How much does it cost to paint a cast iron tub?
How much does it cost to refinish a cast iron tub? For an average cost of $350 to $500—a fraction of the $1,200 to $5,000 expense of a new cast-iron or steel tub installed—refinishers can make an antique fixture look brand new.
Can you use rustoleum on cast iron tub?
The mixture is available in three colors — white, almond and biscuit — that you can use to refinish ceramic, porcelain, acrylic, cast iron and fiberglass tubs alike. There's a bit of preparation necessary before application, but after you complete the prep work, the new finish goes on like a coat of paint.
How do you paint the outside of a cast iron clawfoot tub?
How to paint a tubRemove the legs and other hardware. Take off the clawfeet and any other hardware you can remove from the bottom.Sand the outside of the tub. ... Clean the tub. ... Tape off everything you don't want painted. ... Prime the tub. ... Paint the tub. ... Reattach hardware and install tub.
How do you paint an old cast iron tub?
Remove Rust. The first thing you need to do is make sure your bath is free of rust. ... Prepare the surface. After removing the rust the surface needs to be degreased using sugar soap. ... Prime the surface of the bath. Before applying a coloured paint you will need to use a metal primer. ... Apply an undercoat. ... Paint your bath.
How do you change the color of a cast iron tub?
0:322:55Reglazing a cast iron tub a clean white color - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlong with a with a tile but with the towel holder. And then we soap holder we're going to refinishMoreAlong with a with a tile but with the towel holder. And then we soap holder we're going to refinish that as well you can see what the process is we already have the area covered.
How do you make a cast iron tub look new?
0:343:15How to Refurbish a Cast Iron Tub | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell the inside what we do is we wash it down with an acid solution and that gives the existingMoreWell the inside what we do is we wash it down with an acid solution and that gives the existing porcelain a facelift. It's going to clean the porcelain as well as provide a tooth a profile.
Is it worth refinishing a cast iron tub?
The cast iron tub refinishing procedure also known as cast iron tub reglazing, not only is a viable alternative to replacement when the tub is old, stained, damaged, or simply doesn't look good anymore but has become the number one choice for contractors nowadays when they are hired by a homeowner to remodel a bathroom ...
Can I paint the outside of my clawfoot tub?
Prime: Thoroughly clean the tub's exterior, then apply a quality latex primer with a foam roller and let dry to create a smooth surface. Apply: Paint at least two coats of exterior-grade latex paint in a satin or semigloss finish onto the exterior using a foam roller.
What is the best paint to use on cast iron tub?
acrylic urethane enamelFor a cast-iron or fiberglass tub, you can use acrylic urethane enamel, which may already come mixed for you, or you may have to mix it it, just depending on what kind of kit you purchased. For fiberglass tubs, you can also use a two-part epoxy paint instead of the acrylic.
What is the best paint to use on cast iron?
Oil-based paint designed for use on metal is best for cast-iron items. Avoid using water-based paint made for wood on cast iron.
Is painting a bathtub a good idea?
The answer is YES. Painting a bathtub isn't something most people think to do. In fact, when I started telling people my plan was to paint my pink tub, they either asked how or thought it wouldn't work. Well, I'm here to tell everyone who doubted me that it indeed worked and looks like a million bucks!
What kind of paint do you use on a bathtub?
Regular paint will not be able to withstand water. Acrylic polymer paints are one of your best options for an acrylic bath. Whereas for a cast iron tub, the bath paint must be suitable for metal. An oil-based primer and paint is best for this type of bath.
Can you paint plastic bathtub?
Painting a plastic bathtub can take around 1 to 2 days for the paint to properly dry, with around 4 hours spent on removing the previous bathtub's finish. Keep in mind, the more time you spend cleaning and sanding the existing surface before applying the refinishing paint, the better the paint will stay.
Can you paint a plastic tub surround?
As Miracle Method explains, acrylic enamel is the best material for the job. This can be purchased in a typical tub or in spray bottle. If you do opt for a tub of paint, a small roller tends to work better than a brush to achieve an even and streak-free finish.
What kind of paint did Einstein use?
Some Einstein painted the outside of one of ours with latex paint and it is flaking all over the place.”) (“Don't paint it with a brush or roller. Spray on at least 2 coats of oil-based metal primer. Then spray at least 3 coats of oil-based paint.
What kind of paint does Signature Hardware use?
Signature Hardware uses Sherwin Williams or Porter exterior acrylic latex (they sell a lot of clawfoot tub hardware). (“After removing the paint, make sure to use an oil based primer for metal and oil based paint.
Is latex paint better than oil?
Latex said to be better than oil for flexibil ity as tub warm s and cools (semi-gloss or gloss paint for cleanability) (This comment found: “Using exterior latex paint indoors can cause health problems for some folks due to the higher mildewcide content. My friend found out the hard way.”)
Carolyn252 New Member
We've got an old clawfoot cast iron bathtub. We've stripped the old paint from the outside of the tub. What is the best paint to use now? Should we use latex or oil? Should we prime it or not? (The inside of the tub is in perfect condition and does not need any work.)
Bob NH In the Trades
Tub refinishing can cost an additional $500-$1000. Refinishing is a painting process that will repair defects in the porcelain. The interior of the tub is body-filled, sanded, acid-etched, primed, and painted. The exterior is sandblasted down to the original cast iron, and then primed and painted.
Gary Swart In the Trades
I agree with the epoxy paint and primer. I'd suggest the spray cans of epoxy, you stand a better chance of a smooth finish, but don't let it break your heart if you are less than satisified with how it looks when you finish. Post back when it's finished, some of use would like to hear how it turns out.
How do I refinish the OUTSIDE of a cast iron tub?
We bought a claw foot tub that needs refinishing on the outside. The previous owner had painted half of the tub and the other side has some small rust spots. The tub surface is quite rough and I am not sure how to best refinish it.
Comments (3)
If the tub isn't yet installed, you might want to have the exterior sandblasted to get down to bare metal. At that point, you can prime, then paint with a good quality exterior or marine grade enamel.
How long does a cast iron tub last?
But says Diane Robbins, co-owner of the franchise that resurfaced Jackie's tub, with proper care and maintenance (nonabrasive and bleach-free cleaners only), a refinished cast-iron tub surface should last 15 to 20 years.
What kind of paint does Scott Ayers use on a bathtub?
Enveloped in a mist of paint, Scott Ayers sprays an acrylic urethane enamel over the bathtub’s damaged porcelain.
Who resurfaced the bathtub in Jackie Metropoulos' house?
That's what Jackie Metropoulos chose to do, and hired Scott Ayers, a technician for the Miracle Method franchise in Ludlow, Massachusetts, to resurface the old cast-iron bathtub in the 1919 house she and her husband, Matt, own in Longmeadow, Mass. Their second-floor bathroom has a mix of old charm and new shine, ...
Can you refinish a built in bathtub?
Refinishing may be the most practical way of restoring a built-in bathtub, but for those lucky enough to have a removable claw-foot tub or cast-iron sink, the dream has long been to give it a new finish that matches the hardness and durability of the old one.
How do I paint a tub?
How to paint a tub 1 Remove the legs and other hardware.#N#Take off the clawfeet and any other hardware you can remove from the bottom. 2 Sand the outside of the tub.#N#Give the outside of the tub a light sanding, removing the sheen of the tub’s finish. You want a nice, matte surface for the paint to adhere. 3 Clean the tub.#N#Using damp paper towels, be sure to remove all sanding dust from the outside of the tub. 4 Tape off everything you don’t want painted.#N#BE SURE YOUR DRAIN HOLES ARE COVERED (you don’t want paint spraying through the holes to the interior of your tub!). Then use plastic and quality painter’s tape to tape off the top and lip of the tub so only the bottom is exposed. 5 Prime the tub.#N#Using a high-quality bonding primer, apply a light, even coat to your entire surface. 6 Paint the tub.#N#Once the primer is dry according to package directions, apply a high-quality water-resistant paint. Oil based paints or exterior paints are a good choice for withstanding the damp bathroom. I used this exterior paint in a satin finish.#N#Brush, roll, or spray the paint, careful to avoid brushstrokes. Once dry, sand lightly (if needed) and clean before applying a second coat of paint. Apply a second coat and let dry. 7 #N#Reattach hardware and install tub.#N#And enjoy!!
What paint should I use for a damp bathroom?
Oil based paints or exterior paints are a good choice for withstanding the damp bathroom. I used this exterior paint in a satin finish. Brush, roll, or spray the paint, careful to avoid brushstrokes. Once dry, sand lightly (if needed) and clean before applying a second coat of paint. Apply a second coat and let dry.
Can you restore an old cast iron tub?
Yes! I love the idea of restoring an old cast iron tub to life…. We just didn’t find one that was in good shape and the right size for our space. Be sure to sand off any old, flaky finish. If you have trouble, you could try a little paint stripper to get it clean and ready.
