How to Permanently Disable GM PassLock System
- Remove the appropriate dash panels to get to the wire harness.
- Locate the Pass Lock 2 Wires, they will be coming out of the ignition OR on the BCM they will be located in the grey connector, Pin A6 is your ...
- Strip some of the wire insulation off the black wire, leaving it bare so you can test and solder to it later. ...
Full Answer
Is it possible to disable the PassLock system on a car?
While it is not possible to completely disarm the Passlocksystem, it is possible to fool it into believing that the Vehicles have experienced a failure. How to Reset the Passlock System on a General Motors Vehicle To begin, insert your key into the starter and start your automobile as you normally would, then allow it to stall.
How do I bypass the PassLock 2 system?
Was this answer helpful? The easiest way to bypass the Passlock 2 system is to place a resistor between the passlock sensing wire and the ground reference wire. To find these wires, look for three wires that at some point are wrapped together, coming from the ignition barrel.
How do you disable the PassLock system on a GMC Sierra?
The Passlock system uses a recognition transponder in the ignition tumbler and a computer chip in the ignition key. While you cannot remove the Passlock system, you can disable it by tricking it into thinking the Vehicles had a malfunction.
Is the PassLock feature on my truck dangerous?
Hi, all. The passlock feature on my truck engages occasionally without cause, making me sit and wait out the 10-minute delay. This is always inconvenient and has the potential for being a safety hazard. Does anyone have an idea for how I can permanently disable this feature?
Can you disable anti-theft system?
There are some cars that will recognize the key from you simply turning it back and forth in the door's cylinder. It is best to try both methods: holding the key in the door, as well as turning the key both ways to disable the anti-theft system.
How do I bypass a PassLock GM?
9:5911:10How to Override Bypass GM VATS Passlock 1 2 Passkey Anti Theft ...YouTubeStart of suggested clipEnd of suggested clipLeave your key on for a half an hour. Okay after that time elapses turn your key off turn your carMoreLeave your key on for a half an hour. Okay after that time elapses turn your key off turn your car back on your car will automatically learn this new resistance.
How do I bypass the anti-theft system?
Turn the key to unlock your car door, but don't release it. Hold the key in this position for 20 to 30 seconds. This lets the system know you have the correct key, and it can allow you to bypass the alarm system. Some vehicles recognize the key simply by turning the key back and forth in the door lock key cylinder.
What does GM PassLock disable?
The PassLock system was designed to prevent vehicle theft by disabling fuel to the engine if attempts are made to start the vehicle without the correct bitted key.
Can remote start bypass passlock?
This module bypasses the passlock and allowed the vehicle to remain running after the remote start has been activated. Without it, on most GM vehicles, the vehicle will start with the remote start but will die a second or two later.
Where is PassLock sensor located?
the passlock iii system uses a transponder located under the plastic covering of the key. in most cases, these keys are stamped "pk3" on the metal blade near the plastic covering.
Is there a fuse for anti-theft system?
You can find the alarm fuse in the panel. Look in the owner's manual to find the exact location of the fuse used by the security system. While the fuse is out, the car is not going to start. However, you can reinsert it and hopefully reset the alarm.
How do you bypass an ignition immobilizer?
You can bypass the immobilizer by placing the key in keyhole hence deactivating the car's immobilizer to remote start. The added security with Mobokey allows the security to be activated as soon as the phone moves away from the car, so you don't have to worry about car security.
How do you Immobilise a car?
To immobilise a vehicle, follow these steps:Open the Edit Vehicle screen. From Live Map, do the following: Choose Vehicle status, and then select the vehicle from the list. ... Open the Immobilisation tab.Choose IMMOBILISE VEHICLE.Select a reason for immobilising the vehicle and click CONTINUE.