What is the best glue for LED strip?
which will cause many inconvenient during the led strip light working. The PU (polyurethane) glue is better than epoxy resin glue because of its good Yellow degeneration resistance, good Low-temperature resistance. However, its price is higher as well as the toxicity.
What to look for when buying LED strips?
- You already own fluorescent shop light fixtures, or can purchase them at a low cost
- You have more stringent requirements or needs when it comes to color quality, such as color rendering
- You want to have the ability to easily change your lighting on a regular basis (for example, swapping out different LED tubes for different color temperatures)
How to cut and connect LED strip?
Soldering LEDs Together
- Box cutter or knife
- Soldering iron
- Metal solder wire
- Plastic end caps
- Wire strippers
- Silicone glue
How to cut, connect and power LED strip lights?
In the video, you will learn about the following:
- How to cut COB led strips?
- How to connect COB light strips without soldering wires?
- Which accessories are easy to be use?
- How to configure a more suitable power supply?
Where can LEDs be cut?
1:089:38How to cut, connect & power LED Strip Lighting - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you have found the cut line marked on the LED strip. Simply use the scissors to cut directlyMoreOnce you have found the cut line marked on the LED strip. Simply use the scissors to cut directly along the line as demonstrated. Here it's important to note that LED strip must only be cut at the
Can you cut LED strips in the middle?
0:012:20What happens if you cut your LED strip lights in the wrong place?YouTubeStart of suggested clipEnd of suggested clipSo if you do cut it in the middle of the section. It. Will only work all the way up until that pointMoreSo if you do cut it in the middle of the section. It. Will only work all the way up until that point and it won't work afterwards. Because there's no completed circuit if you've ordered your LEDs.
What happens if you cut your LED lights wrong?
A: If the LED light strip you purchased can be cut, the remaining part that you have cut off cannot be used anymore. If you want to reconnect them after cutting, you must use an additional 4 pin connector to reconnect.
Will my LED lights work if I cut them?
Due to their design, LED Strip Lights will continue to work even after they have been cut. This is because their circuit is completely closed at each cutting point. If you are removing a section from the end of your strip light, always make sure you are cutting it at the end away from the connector.
How to get rid of pre-fitted LED strip?
There are two methods of doing this. One is by using a strip connector and the other is by soldering a new socket onto the strip . The easiest way of doing this is by using strip connectors.
How long are LED strips?
LED strips are usually sold as long reels. There are 3 feet and 16 feet long LED strips. If these lengths are longer than what you actually need for your home project, it is possible to cut the strips in lengths that you require. But, will they still work if they are cut down?
How to clean copper pads?
With a knife, start by cutting away the translucent plating or silicone covers on the copper pads. Using rubbing alcohol and a small brush, clean the strip thoroughly.
What is LED strip light?
LED strip lights are decorative lamp belts made up of individual LED emitters and mounted on a narrow, flexible circuit board. It is half an inch or 10 to 12mm wide and operates on low-voltage DC power. They are also known as LED ribbon lights or LED tape lights. In the back of the LED strip is a double-sided adhesive.
Why do I need to test my LED lights before cutting?
If you locate these copper dots, then you will see the cutting line in between them. Before cutting, you need to test your lights first to see if they are working. The reason for this is that cutting your LED will surely make your warranty void. Then determine the length of the LED strip that you need for your project.
Where are the copper dots on a black cutting line?
You will also find copper dots on both sides of the black cutting line. The pattern they form is symmetrical. There are 2 copper dots on single color lights but on color changing RGBs, you will find 4 copper dots. If you locate these copper dots, then you will see the cutting line in between them.
Why are LED strips marked?
These are marked so that you can cut them safely and not damage them. There are many individual circuits that make up your LED strips. The cut lines indicate where one circuit ends and where the new one starts. If you don’t cut your LED strip on the cut line but somewhere else, then the circuit, or the whole strip, will stop working.
Where to cut an LED strip
While LED strip lights are adaptable, it’s important to cut them in the right place to make sure they continue working. LED strips are made up of multiple individual circuits. The designated cut lines mark the end of one circuit and the beginning of another.
Cutting and reusing Hue lightstrips
Want to reuse the cut-off piece of a LED light strip? No problem — especially with the Hue lightstrip V4, which comes with a connector to reuse cut parts with other Hue lightstrips. This means leftover pieces won’t go to waste, and you can further customize the placement of your LED strips.
How to bend an LED strip
LED lightstrips are designed to bend with ease. If you want to curve your light strip around surfaces, or the back of your TV or computer screen, there are two options to do so effectively.
How to connect LED strip to LED light?
1. Align the quick connector with the LED strip. Quick connectors can be purchased along with LED lights and are hassle-free ways of completing the electrical circuit. The LED will have a + and - printed on the back. Line up the connector’s black wire with the - and the red wire with the +.
How do LED strip lights work?
LED strip lights are designed to be easy to cut apart with a pair of scissors. Each LED has a pair of copper dots at the end. As long as you cut between the dots, all of the LEDs will work. From there, you can connect the LEDs to a power source either through a quick connector or by soldering.
How to remove copper dots from LED lights?
1. Scrape the plastic cover off the end of the LED strip. Use a sharp knife or box cutter. Cut into the plastic right above the copper dots at the end of the LED. Remove enough plastic to expose the copper dots, then scrape the blade along them to clear off any plastic debris.
What do the copper dots on a light strip mean?
The copper dots indicate where each light connects to the next one on the strip. You will see a dotted cut line running between the copper dots. Choose the line closest to the LED length you measured earlier. The line is the only place you can safely cut the LEDs.
How to connect LED lights to power source?
Measure out the length of wire you need to connect the LED to your power source. Leave a little extra length, about 1⁄2 in (1.3 cm), on the end of each wire. Slide the wires through the small hole you cut into the cap earlier, not the larger opening.
