What's the best way to cut metal Curtain Poles?
I had to do something similar last year with two metal curtain poles. I used a Bahco hacksaw like the one linked. I used a blade with a reasonably high number of TPI. As posted above, use masking tape around where you want to cut, draw the cut line on this and then use the hacksaw.
Can I use a curtain pole for heavy curtains?
Slim metal curtain poles are not designed to take very heavy weight curtains either and are more suited for sheer curtains, voile panels or lightweight lined curtains.
Can you cut metal curtain rods with a miter saw?
Or, as long as you have a fine metal blade, you can use a powered miter saw. Make sure to buy metal curtain rods that are hollow core if you plan to cut them to size yourself.
How to cut a steel pole?
How to Cut a Steel Pole. 1 Step 1. Fit your saw with a carbide blade. Carbide is an extremely hard material mixed into metal saw blades to allow them to cut steel and other ... 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5. More items
How to cut a pole with a circular saw?
How to separate a melted pole?
How to get a good grip on a bandsaw pole?
Can you cut a steel pole?
Can you cut curtain pole size?
All metal and wood poles can be cut down to size, but remember that once cut, they cannot be returned to store.
How do you cut a aluminum curtain track?
If you need to cut your track to fit your window, use a fine tooth saw or hacksaw. To provide an overlap, the track must be cut to allow sufficient length for each half of the window plus an additional 10cm on one half of the track.
Can you cut a curtain rod with a pipe cutter?
0:471:42How to Cut Down a Wrought Iron Pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt what we use is a plumbing pipe cutter this is a product widely available at just about anyMoreIt what we use is a plumbing pipe cutter this is a product widely available at just about any hardware store to see clamp with a dial. Inside.
How do you adjust curtain rod length?
Adjusting a Tension Rod:Remove or shift the existing curtain. If curtain rings are holding the curtain to the tension rod, remove the curtain rings. ... Loosen the tension rod. Grasp the tension rod near one end cap and pull downward. ... Adjust the tension and length of the rod. ... Test the tension rod. ... Replace the curtain.
How do you cut a metal pole?
1:222:34How To Cut Metal - Ace Hardware - YouTubeYouTubeStart of suggested clipEnd of suggested clipTowards you and start cutting. And allow the saw to do the work. If you push too hard. You'll. FindMoreTowards you and start cutting. And allow the saw to do the work. If you push too hard. You'll. Find then it'll bind as well. But it's back and forth even strokes.
How do you remove the end of a curtain rod?
Examine one of the finial ball ends of the curtain rod. Twist the ball counterclockwise while holding the rod steady. If the ball loosens, continue twisting until it is off the curtain rod. If it does not loosen, repeat the process with the other end.
How do you cut a hollow metal rod?
0:030:30Cutting Clothing Rods - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a hacksaw or plumber's tubing cutter to cut the rod install rod stops and snap the rod into theMoreUse a hacksaw or plumber's tubing cutter to cut the rod install rod stops and snap the rod into the rod clips.
How do you turn a curtain rod into a pipe?
0:194:51DIY Custom Curtain Rod - Steel Pipe - 15 FEET LONG - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust fit right through it. And we'll cap the ends. One inch to a half-inch reducer T if the tunersMoreJust fit right through it. And we'll cap the ends. One inch to a half-inch reducer T if the tuners nipple to instantly and half inch flange plate. And the nipple goes right there that.
Can you cut down a shower curtain rod?
Place the coping saw blade directly on the marker line of the shower curtain rod. Keep the blade straight up and down to avoid making an angled cut. Place the blade end that is closest to your hand on the mark, and pull back on the saw to make your first cut. There will actually be a slight cut mark at this point.
How do you cut aluminum sliding door tracks?
2:024:12Q & A - How to extend a metal conduit curtain rod. - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow if you needed a different length if you needed it shorter you could just cut it with a metal cutMoreNow if you needed a different length if you needed it shorter you could just cut it with a metal cut-off saw or whatever you have that will cut metal.Q & A - How to extend a metal conduit curtain rod. - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you extend a curtain rod that is too short?
How do you cut aluminum closet tracks?
8 to 12 inchesAdditionally, be sure to choose a curtain rod that's wider than your window. This allows curtains to be pulled completely to the side of the window and makes the space feel larger. The rod itself should be 8 to 12 inches longer than the window's width, which allows for 4 to 6 inches on either side.May 10, 2022How to Hang Curtains Correctly the First Time | Better Homes & Gardenshttps://www.bhg.com › window-treatments › basics › how...https://www.bhg.com › window-treatments › basics › how...Search for: How much longer should curtain rod be than window?
What do you use to cut metal curtain rods?
between four to six inchesA rule of thumb (from Architectural Digest) is that curtains should be hung between four to six inches above the window frame, so install your curtain rod accordingly. When you hang the curtain rod high, it will make the window appear taller.Oct 13, 2021How to Hang Drapes at the Proper Height - The Family Handymanhttps://www.familyhandyman.com › article › proper-heig...https://www.familyhandyman.com › article › proper-heig...Search for: How high above window should curtains hang?
How do you cut a curtain pipe?
0:131:49How to Cut an Aluminum Astragal to a different Length - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a hacksaw or power miter saw cut the astragal body and the strike plate housing at the sameMoreUsing a hacksaw or power miter saw cut the astragal body and the strike plate housing at the same time make sure the strike plate housing does not.
How to cut a pole with a circular saw?
Cut the pole. If using a circular saw, squeeze the trigger hard and push the saw firmly, evenly and slowly into the pole until it has cut all the way through. With a hacksaw, this will take much longer, as you will be relying on the power of your arms and hands.
How to separate a melted pole?
Knock the pole with a hammer to separate it if it doesn't break cleanly once your cut is done. Some of the melted material may stick in the cut, but it is brittle and will break easily.
How to get a good grip on a bandsaw pole?
If the pole is small enough to fit in a bandsaw, set it across the bandsaw deck, start the saw, then get a good grip on the pole on either side of the blade and push it through firmly and slowly.
Can you cut a steel pole?
Steel poles are a common sight as flagpoles, railings and fences or supporting scaffolding or basketball nets. To fit and install any of these things, it may be necessary to cut a steel pole down to size. Since steel poles are typically hollow, cutting them is less work than it might appear from the thickness of the pole itself.
Can you cut a curtain pole with a hacksaw?
Metal curtain poles can be cut with a hacksaw, or for a totally square cut, use one of our special curtain pole cutters. Wooden curtain poles can be cut with a fine tooth wood saw. Helpful Hint: Always remember that when you are cutting a curtain pole that is in two pieces you must trim equal amounts from each side.
Can a mitre saw cut metal?
Cutting Metal Closet Rod. Mitre saw with a stop and a blade appropriate for cutting ferrous or non-ferrous metal, de pending on what the rod is made out of. If the lengths are longer than what you can do with a stop attached to the saw's fence, it is pretty easy to rig up something.
Can you cut a curtain rod?
Wooden drapery rods and metal curtain rods can be easily cut to size before you install them. Most hollow core metal drapery rods can be cut using a hacksaw with a fine cutting blade. Or, as long as you have a fine metal blade, you can use a powered miter saw.
How to cut a cylinder with a hacksaw?
As posted above, use masking tape around where you want to cut, draw the cut line on this and then use the hacksaw. Take your time - cutting into the cylinder takes time. Once you've done that, cutting through the cross section is easier because there's less metal to cut.
Can you attach finials to metal?
Yup I'd recommend that. I didn't have a metal file at the time so didn't bother. Had no issues with attaching the finials.
How to cut a drapery rod?
Then, wrap two inch masking tape around your rod over the mark you just made. You'll want your saw to cut through the masking tape and then through your pole.
How long should a curtain rod be?
You'll quickly notice that most curtain rods come from the manufacturer in several predetermined lengths like four foot, six foot and eight foot. This works great if your window is really close to one of these sizes, but if you need a slightly smaller length of drapery pole for your project, then you'll need to trim it before you install it.
How deep should a pilot hole be for a drapery rod?
Your mark should be at the center point. You can use a 1/8 inch drill bit to make the pilot hole, or you can simply tap in a nail. The pilot hole doesn't need to be very deep, usually a half inch or so is all you'll need to start the finial into the end of the drapery rod. Many drapery hardware products can be cut to size before they are shipped ...
How to cut hollow core drapery?
Solid metal drapery hardware is best cut to size by the manufacturer. To trim your hollow core product to size, simply mark the point where you need to make your cut and use your saw. Before you cut, make certain to remove any finial adapters or plugs from the end of the pole so you can slide them back on when you're finished. ...
Can you trim a curtain rod to fit a window?
Both decorative wooden drapery rods and metal curtain rods can be quickly trimmed to perfectly fit your window. And, the process is similar for both the wood and metal styles. Before you begin, make sure you have access to the appropriate saw as well as safety glasses or goggles.
Can you use a miter saw to trim drapery?
For trimming wood drapery rods to size, you'll get the best results with a powered miter saw. If you don't have a miter saw, you can always use a hand saw. Make sure your hold the drapery pole firmly in place while you cut if you're using a hand saw.
Do you need to trim drapery poles before installing?
This works great if your window is really close to one of these sizes, but if you need a slightly smaller length of drapery pole for your project, then you'll need to trim it before you install it. The task of cutting drapery hardware to size can seem a bit scary to some home owners.
Where are curtains located on a curtain pole?
The main set of curtains are usually located on the front pole , with nets or voiles fitted on the back pole. Great for privacy issues and will also camouflage an unattractive view while still allowing daylight into the room. Click here to view all Double Metal Curtain Poles. Eyelet and Tab Top Curtain Poles.
What is double curtain pole?
Double Curtain Poles. Double curtain poles may be purchased as sets, or made up using components from the "Create Your Own Curtain Pole" range. Double pole sets allow you to dress your windows with two pairs of curtains or voiles and curtains.
How to measure the height of a curtain pole?
If you already have your curtains, then to determine the height of the position of the curtain pole above the window (A) you will need to measure the drop of the curtains and add the measurement from the top inside of a curtain ring to the bottom outer edge for heading which will hang from the curtain rings.
How to measure for a short curtain?
For a short curtain use the drop length to measure from approx.12cms below the sill to mark the height (B) for the bracket location above the window recess, for curtains to sit on the sill measure from here instead, plus 0.5cm for clearance.
How to keep curtains from marking when hanging?
Cleaning the area with a vacuum cleaner as soon as you have fitted the brackets will keep your curtains from becoming marked when you hang them.
How to replace a pole?
To replace an existing pole with a new one, simply measure the total length of the existing pole excluding the finials. This will give you the total pole length you require to start shopping.
Why use a metal tape measure?
A metal tape measure is recommended for accuracy and ease of use.
What size curtain poles do Terry's have?
At Terry’s we carry a range of 16mm, 28mm curtain poles and a 35mm wooden curtain pole too. 16mm Metal Curtain Poles - Our 16mm diameter metal curtain poles are ideal when there is limited fitting space above a window.
What is a 16mm metal pole?
Our 16mm metal poles are slim and very discreet looking and because they are less weighty than our thicker metal poles, they don’t need overly long or robust fixing brackets, but instead tend to have very compact, neat looking brackets that need little fixing room. Slim metal curtain poles are not designed to take very heavy weight curtains either and are more suited for sheer curtains, voile panels or lightweight lined curtains.
What is 28mm pole?
These poles come with sturdy and adjustable cast angle brackets which provide excellent support for this thicker pole. 28mm metal poles are desirably more obvious and substantial than our thinner metal poles and therefore play a more significant and deliberately obvious part in styling your window dressing. These metal curtain poles are great all rounder’s and will cope with everything from voiles and lightweight lined curtains to medium to heavy weight curtain fabrics. 28mm metal curtain poles are also the perfect diameter poles for hanging eyelet (sometimes know as grommet or ring-top) curtains.
Can I use 16mm curtain poles with eyelet curtains?
16mm metal curtain poles are not recommended for use with eyelet curtains because the compact brackets do not hold the curtain pole far enough away from the wall to accommodate the depth of the folds created by eyelet heading. 28mm Metal Curtain Poles - Our extensive range of 28mm metal curtain poles is by far and above our best selling collection of curtain poles. Excellent quality and fabulous value for money our 28mm metal poles are a reliable and stylish multi-purpose pole.
Can you use a metal curtain pole alone?
Some people think that a metal curtain pole alone isn’t enough to bring out detail in a room and is there just to do a mundane job. But think about co-ordinating that metal pole with other fittings in your room such as light fittings, wall lights, lamp bases, door handles, picture frames or ornaments and you’ll have the makings of a striking collection of metallic accessories that can really pull an interior scheme together.
Do curtain poles fall down?
All our metal curtain poles come with high quality cast metal brackets that will not bend or break. It is a myth that metal curtain poles eventually fall down because the brackets are not strong enough.
How to cut a pole with a circular saw?
Cut the pole. If using a circular saw, squeeze the trigger hard and push the saw firmly, evenly and slowly into the pole until it has cut all the way through. With a hacksaw, this will take much longer, as you will be relying on the power of your arms and hands.
How to separate a melted pole?
Knock the pole with a hammer to separate it if it doesn't break cleanly once your cut is done. Some of the melted material may stick in the cut, but it is brittle and will break easily.
How to get a good grip on a bandsaw pole?
If the pole is small enough to fit in a bandsaw, set it across the bandsaw deck, start the saw, then get a good grip on the pole on either side of the blade and push it through firmly and slowly.
Can you cut a steel pole?
Steel poles are a common sight as flagpoles, railings and fences or supporting scaffolding or basketball nets. To fit and install any of these things, it may be necessary to cut a steel pole down to size. Since steel poles are typically hollow, cutting them is less work than it might appear from the thickness of the pole itself.
