Trex products should not be ripped to reduce thickness, but can be ripped to reduce width. As long as the board can still be installed per the installation instructions, the warranty will be valid. Please use care when fastening ripped boards, as pre-drilling may be necessary. Does Trex decking get hot on a sunny day?
How to repair deep scratches on Trex deck?
Here are a few ways to keep scratches at bay and maintain your deck:
- Use a woven rug designed for high-traffic spaces. A woven rug will help keep foot traffic from shoes from doing damage. ...
- Place pads under pieces of furniture that live on your deck. ...
- Put furniture away when it’s not in use. ...
- Use a broom instead of a shovel to clear leaves, snow or other debris. ...
What is the recommended joist spacing for Trex decking?
What Is Frame Spacing for Trex Decking?
- Significance. Trex and other composite decking brands are considerably heavier and more flexible than wooden surface boards.
- Building New. When designing a new trex or composite deck, the spacing between floor joists should be 12 inches on center.
- Replacing Old. Wooden decks will have a frame spacing measurement of either 24 or 16 inches. ...
How to clean your TimberTech deck?
To prepare your traditional wood deck before the winter season:
- Remove any mold and mildew with chemical cleaners.
- Use a power washer or hose to rinse the deck thoroughly.
- Let dry for 24 to 48 hours.
- Re-stain and re-seal (be aware that stains and seals often release volatile organic compounds, or VOCs, and other harmful chemicals into the air, so use with care).
How to repair Trex deck?
Method 1 Method 1 of 2: Fixing Scratches, Splits, or Chips Download Article
- Purchase a repair kit if you want to easily fix your deck. ...
- Sand the scratch with a scratch repair pad or applicator tool. ...
- Apply wax to the damaged area until it is level. Take off the tip of the wax stick, and rub it over the sanded area.
- Rub the applicator over the wax to remove any excess. ...
How do you rip Trex boards?
You can make simple cross cuts in composite decking the same way you would cut any soft pine—a power circular saw will work fine. A power miter saw can provide very accurate, straight cuts, and a table saw with support extensions can make all types of cutting easier.
Can you rip a composite deck board?
Can composite decking be cut? Yes, you can cut most composite decking just like wood — no special tools required.
Can Trex be repaired?
If you notice a scratch or damaged area on your Trex decking, fret not! If you have a small scratch or chip, use a composite deck repair kit. If you have a larger scratch, dent, or dings, it is best to replace the entire board. With a few tools, you can easily repair your deck and enjoy your patio.
Can you remove and reinstall Trex?
An existing Trex deck needs to be relocated on a house and the wear surface “boards” need to come up for later reinstallation. They are installed with countersunk hex-head screws and over 50% are stripping out in a test area.
How do you repair a composite deck?
7:4510:34How to install a composite deck with Wickes - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlways use screws that are specifically designed for the job and make sure that all screws areMoreAlways use screws that are specifically designed for the job and make sure that all screws are secure. But not over tightened. Work your way down the board fixing the deck board to each support joist.
Can you cut composite decking lengthways?
0:032:11How To Cut NeoTimber® Composite Decking Boards - YouTubeYouTubeStart of suggested clipEnd of suggested clipNumber one the miter saw this saw can deliver smooth and accurate cuts along the length of yourMoreNumber one the miter saw this saw can deliver smooth and accurate cuts along the length of your composite decking. And is an excellent tool for achieving.
How do you repair a Trex deck?
Here are some methods you can use to fix scratches on your composite deck:Fill nicks and scratches with an epoxy-based filler and a putty knife. ... Try the heat method. ... Replace scratched boards with new ones. ... Consider consulting the manufacturer or retailer about your scratched decking.
How do you fix a hole in a Trex deck?
Fill small holes, using a putty knife, with a mixture of fine composite board shavings and silicone caulk. The consistency of the mixture should be thick enough that it will not seep out of the bottom of the hole. Match the color of the caulk to the deck boards.
Why is my composite deck peeling?
0:171:48Common Composite Decking Problems - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe most common problems composite deck owners face are algae mold and surface peeling many believeMoreThe most common problems composite deck owners face are algae mold and surface peeling many believe that moisture is the primary.
Can composite decking be lifted?
Therefore, composite decking boards can easily lifted if required without causing unnecessary damage and replacements.
How do you rip deck boards?
4:078:13How to remove old deck boards. The easy way. - YouTubeYouTubeStart of suggested clipEnd of suggested clipYeah that's a little trick I learned years ago just take your grinder. Grind the top heads. Off theyMoreYeah that's a little trick I learned years ago just take your grinder. Grind the top heads. Off they could be screws or nails. So did you grind them it'll pop right up.
How do you remove deck boards without damaging them?
0:482:47How-To Easily Remove Rotting Deck Boards That are Nailed to your DeckYouTubeStart of suggested clipEnd of suggested clipDown. Show you so again you just wedge wedge the crowbar down and wedge it down and you work yourMoreDown. Show you so again you just wedge wedge the crowbar down and wedge it down and you work your way with these two wedge. Sledge her crowbars down and then work your way.
What is Trex decking?
Trex means quality, beauty and minimal maintenance, saving you time, money and everything that comes with a call to the handyman. Plus, the high-performance composite shell of Trex decking resists rotting, staining and cracking.
Where is Trex decking used?
and around the world, ranging from a landing at Mt. Rushmore and a resort in Dubai, to a pier in Philadelphia and New Jersey-shore boardwalks replacing those destroyed by Hur ricane Sandy. Of course, Trex is more than just decking.
How much does a Trex deck cost?
The cost of a Trex deck typically runs from $9 to $16 per square foot. As with many things in life, you get what you pay for. Initially, Trex decking and railing does cost more, board for board, than wood decking and railing.
How much plastic is recycled in Trex?
That makes Trex one of the largest plastic film recyclers in the U.S. In fact, the average 500-square-foot composite Trex deck contains 140,000 recycled plastic bags.
Can you use area rugs on Trex decking?
Most area rugs aren't a problem with Trex decking, but we do recommend cleaning underneath them regularly. In rare cases, rugs made of plastic or viscose materials may bleed, drawing colorant out of the decking or making them difficult to remove. Always allow your decking to fully dry before fitting a rug into place.
Is Trex code compliant?
All Trex products, when properly installed for approved applications, are either code compliant or are undergoing rigorous code compliance review for the International Residential Code (IRC) and/or the International Building Code (IBC). Check with your local building code department for jurisdictional requirements.
Is Trex decking a residential or commercial?
Of course, Trex is more than just decking. The sleek profile of Trex Signature® railing works as well for commercial and multi-unit residential complexes as it does for your own backyard, while Trex Outdoor Furniture™ can be found in many coastal resorts under Trex Pergola™ installations.
How much space between decking boards?
Between end-to-end boards, allow a 3/16-inch space.
Why do builders like composite decking?
Builders like composites because they are relatively easy to install–the materials are very consistent in size and quality, come in lengths up to 20 feet long, and are not prone to warping and cracking. Composite decking won’t rot or splinter (an extra bonus for bare feet).
Can composite decking be fastened to treated wood?
This will increase the longevity of the deck and also prevent bowing during the hottest part of the day. Composite decking can be fastened to treated wood joists with screws or with hidden fasteners. Using composite deck screws is critical because they are specially designed to help hold the material in place.
Does composite decking rot?
Composite decking won’t rot or splinter (an extra bonus for bare feet). New styles also have fire prevention technology incorporated into the composite, which reduces the risk of house fire during cookouts and makes them less of a fire hazard where wild fires can be a threat.
Can Trex be cut?
Composite decking such as Trex can be cut, drilled, and fastened just like traditional wood, but there are a few tricks you should know to make your project easier, and provide a more professional finish. Composite decking can mimic the look of natural wood. Trex.
Is vinyl decking low maintenance?
Vinyl decking is yet another low-maintenance option, although one that offers a particularly non-traditional deck. Installation differs as well. In general, first an aluminum or vinyl track is installed across the joists, and then top pieces are snapped into place.
Can composite decking be used as structural material?
Composite decking cannot be used as structural material. This means that any load bearing area will need to be framed and supported before the composite material can be attached. When building your deck and railing, it is recommended that pressure treated wood be used as the framing and floor joists.
What is Trex decking made of?
Trex decking is made from 95% recycled materials, including reclaimed timber and sawdust as well as recycled plastic from many common household items, such as the plastic overwrap on packaging for paper towels and toilet paper, dry cleaner bags, newspaper bags, grocery and shopping bags. Trex annually salvages and keeps more than 400 million pounds ...
Why is Trex better than timber?
Why are Trex ® outdoor living products better than timber? Top. Trex products offer superior durability and performance that you can’t get from timber. Trex decking resists termites, won’t rot, warp, or splinter and never needs staining or painting.
What can I use to melt snow off Trex decking?
Calcium chloride or rock salt can be used to melt ice and snow on Trex decking. Care should be taken to rinse off when the weather makes this practical. Use plastic shovels (never metal) to remove snow and ice. A metal shovel can possibly chip the decking surface and void the warranty.
What is Trex Enhance?
Newer-generation Trex deck boards (Trex Transcend ® and Trex Enhance ®) are manufactured with a high-performance shell that wraps around the composite board to protect it from the elements, providing resistance to fading, staining, scratching and mould . In addition to improved performance, the shell technology offers:
How do I clean a deck board?
Spray deck with soap, and then follow by gently scrubbing each deck board with a soft bristle brush. Spray/rinse each individual deck board using fan tip no closer than 8” from the decking surface. RINSE THOROUGHLY. If dirty water from cleaning is left to dry, this will cause a film to remain on the decking surface.
How much plastic is recycled in Trex?
That makes Trex one of the largest plastic film recyclers in the U.S. In fact, the average 500-square-foot composite Trex deck contains 140,000 recycled plastic bags.
Is Trex decking maintenance?
Is Trex decking no-maintenance Top. Trex decking requires far lower maintenance than wood decking, but does require some maintenance to keep it looking good throughout the years, much like washing your car. For early generation composite decking (Trex Accents), periodic cleaning with a deck wash is required.
How far apart should I lay Trex decking?
1. Protect your substructure. Trex can be installed over timber, steel or aluminum substructures with joist centers at a maximum of 400mm apart.
How far apart should Trex hideaway screws be?
The Universal Fasteners connect two boards together if you drill downwards, directly into the joists. They should be no more than 25mm from the end of the board.
How long does Trex decking last?
With Trex Decking there are a few do’s that you want to follow to make sure installation goes well and that the product lasts for years. Of course, just like everything, there are the don’ts that you want to avoid so your Trex Decking stays looking superior. Renovating your home is always a good idea.
What is Trex decking made of?
What Trex decking is, though, is a composite material that is made from recycled materials such as wood fibers, plastic, and a bonding agent designed to hold it all together. What you are left with is something that looks a whole lot like wood, but which is a good deal stronger and sturdier.
What does Trex look like?
Trex Decking Looks Like Plastic. Today this is a myth, but was not back in the day. When Trex decking first made its appearance, it did not resemble real wood and did have a plastic look. After decades, production has been fine-tuned and Trex decking now looks like real wood.
What is Trex lattice?
The Trex decking lattice is made from the same material as the decking so it has the same characteristics give it lifelong longevity.
Is Trex decking expensive?
Trex Decking is Expensive. This was true back when composite decking was first introduced. In the beginning, Trex decking was about three times more expensive than a traditional wood deck. With improvements in manufacturing and technology, the price has come down significantly. M.
Is Trex decking worth it?
You should never compromise on quality when it comes to building a composite deck. Even if Trex is an expensive composite, building a Trex deck will always be worth it in the long run. It is always better to spend a large amount once instead of spending hundreds on maintenance and up keep every year.
Can you sand a Trex deck?
There are many companies that offer products that can be effectively used on your Trex deck in order to get rid of termites and other insects. Don't Perform Sanding. Sanding is considered important or even necessary for traditional wood decks, however extensive sanding of composite decking should always be avoided.
