A Comprehensive Stihl Bar Size Chart (All Models Included)
| STIHL Models | Pitch | Gauge (inch) | Bar Length (s) | Type of Bar |
| MS 170, MS 171, MS 180 C-B, MS 180 C-BE, ... | 3/8” STIHL PICCO TM Micro TM Mini | 0.043 | 12” 14” 16” | R R R |
| MS 192 C-E, MS 192 T, MS 192 T C-E, MS 2 ... | 3/8” STIHL PICCO TM | 0.043 | 12” 14” 16” | R R R |
| MS 192 C-E, MS 192 T MS 192 T C-E MS 200 ... | 3/8” STIHL PICCO TM | 0.050 | 12” 14” 16” | LW LW LW |
| MS 230, MS 230 C-BE, MS 250, MS 250 C-BE | 3/8” STIHL PICCO TM | 0.050 | 12” 14” 16” 18” | R R R R |
Will a chainsaw bar fit a Stihl Chainsaw?
To fit, a replacement bar for a Stihl chainsaw should have the same mount type and chain pitch as the saw; the bar and chain should further have matching pitch. We will next start with a short recap of chainsaw bar compatibility.
Can you put a longer guide bar on a chainsaw?
Most chainsaws ship with a guide bar that is reasonably sized relative to the saw capacity, but could actually run a longer one. Swapping the original bar for a longer model is often useful, as it may give you just the bit of additional cutting capacity you need in felling or bucking.
What happens if you increase the length of your chainsaw bar?
Another thing to keep in mind, is that as you increase the length of your chainsaw bar, the cutting performance will decrease. So as you move towards the upper end of the bar range, you can expect your chainsaw to cut with a bit less power. It’s a trade-off between the length of the cut, and the power applied to the chain.
What size bar do I need for a Stihl mower?
Finally, the Stihl gives 12” to 16” as the recommended bar length range for this model. The MS 170 takes a 12” to 16” bar with a 3005 mount, 3/8”P (Picco) pitch, and either .043” or .050” gauge.
Can you put a 20 inch bar on a 18-inch saw?
Changing the bar and chain on your 18-inch chain saw to a 20-inch size will enable easier cutting of larger trees and branches. Larger chain saws cut through thicker trees and limbs.Sep 26, 2017
Can you switch chainsaw bar length?
Replacing your chainsaw bar will require a few measurements. Most chainsaws can operate up to three different bar sizes. Guide bars are measured in length, from the tip of the bar to the heel, and range in size from 14 to over 40 inches.
Can I put a longer bar on chainsaw?
Yes, but you need a bar designed to fit on your saw. There are different designs for different saws, and the bar has to match the chain/sprocket configuration as well. Your best bet, if you want to do that, is take it to a dealerto be sure that everything matches up.Jul 27, 2007
Can you put a longer bar on a Stihl MS250?
Stihl does not make 3005 mount bars in anything longer than 18"/68DL (. 325") or 18"/61DL(3/8"P). The 3003 mount bars from the MS260/270/280/290 will not fit on a 250.Aug 2, 2015
Can you put an 18 inch bar on a Stihl ms180?
Yes you can use any brand of bar and chains providing the mounting pattern suits the ms180 (3005 mount). You can also change gauge from .Dec 30, 2015
Can you put a 18 inch bar on a 14 inch chainsaw?
Different Bar Sizes A Poulan 14 chainsaw can operate with a bar that's 12, 14, 16 and 18 inches length. However, a larger bar may not always give the best cutting performance.
How big a tree can a 16 chainsaw cut?
16 chainsaw would cut through a 14″ tree diameter. 10 inch chainsaw for 8″ in diameter. 6 inch chainsaw can cut a 4″ diameter.
What size bars does Stihl make?
STIHL guide bars range from 10" (found on our tree-trimming pole pruners) to an incredible 59" (used in extreme felling operations).
How long is a 16 inch chainsaw bar?
Measure the bar from end to end to find its true length. For example, if the measurement is 16 1⁄3 inches (41 cm), then the true length of the bar is 16 inches (41 cm). Standard chainsaw bar lengths are between 8–24 inches (20–61 cm).
Can you put a 20 inch bar on MS 250?
amateur cutter 20" . 325 bar likely came off an MS 290. To run 20" on a 250 saw you'd probably need to go to lo pro chain. As XXL stated it's not likely to fit the saw anyway.Mar 10, 2018
What size bar can you put on a MS 250?
A combination of features and a high power-to-weight ratio makes this one of the best homeowner chainsaws on the market. Available with 14"/35cm, 16"/40cm or 18"/45cm guide bars.
Will a Oregon bar fit a Stihl?
The AdvanceCut guide bar features a small radius multi-rivet nose for good durability and control. Contact Oregon Customer Support to ensure the best fit for your chainsaw. Fits Stihl 024, 026, 026P, 030, 031, 029, 036, MS 280, MS 271, MS 270, 028, 032, MS 290, 034, MS 260.
What should a replacement bar for a Stihl chainsaw have?
To fit, a replacement bar for a Stihl chainsaw should have the same mount type and chain pitch as the saw; the bar and chain should further have matching pitch. We will next start with a short recap of chainsaw bar compatibility.
What is the minimum bar length for a Stihl chainsaw?
The minimum bar length recommended by Stihl is 10” or 12” for small (35 cc and under) gasoline-powered, battery or electric chainsaws, and 16” for medium-sized and large gas saws. I suspect this minimum is related to kick-back safety.
What size bar mounts does a Stihl chainsaw use?
At current, Stihl chainsaw and bars use three (3) different bar mounts: the small 3005, the medium 3003 and the large 3002. These are not interchangeable: if your saw has a 3003 mount, so must your bar.
How many different rollomatic bars are there?
There are really six different lines of Rollomatic bars, ranging from the small “E Mini Light” up to the “Super E”. The main thing to note here is that the Rollomatic model names indicate different bar constructions and profiles, not compatibility. Specifically, not all Rollomatic bars are interchangeable.
What are the two things that guide bars need to be compatible with a chainsaw?
The matching principles are simple, and can be summarized in one paragraph: To be compatible with a given chainsaw, a guide bar must essentially have only two things: 1) the right bar mount and 2) same chain pitch as the saw.
Can a Stihl bar be matched to a chain gauge?
To be further compatible with a certain chain type, a bar should also be matched to 3) the chain gauge. These matching principles apply to Stihl bars just as to all other brands: when searching for a compatible replacement bar for your Stihl, just look for bar s with the same mount and pitch as your saw.
Do chain and saw have the same pitch?
The saw, bar and chain all must have the same pitch. In practice, the drive sprocket on your saw determines the pitch of the bar & chain. The bar and chain must have the same gauge. (The saw powerhead does not care about the gauge.) You can choose your chains to match the pitch of the bar, or the other way around.
How big of a bar can a Stihl saw handle?
Saws designed to be used by professional arborists in trees, the MS 192 and MS 201 models, can take guide bars between 12 and 16 inches. Stihl's electric saws come in three different sizes: the MSE 140 can handle a bar between 12 and 16 inches, the MSE 180 can take a bigger 18-inch bar, and the MSE 220 takes a bar between 16 and 20 inches.
What size bar does a Stihl arborist saw take?
The professional models vary greatly in size, from the MS 150 arborist saw, which is equipped with a 12-inch bar, to the massive MS 880, whose 121.6 cc engine can handle a 59-inch bar. In the middle of the range, models include the MS 261, which can take a bar between 16 and 20 inches; the MS 362, which can accommodate a bar up to 25 inches; the MS 441 and MS 461, which can accept a bar up to 32 inches; and the MS 660, which takes a bar up to 36 inches.
What is a chain saw guide bar?
A chain saw's guide bar determines the size of timber the saw can cut, and the size of a saw's engine determines, in large part, how long a bar the saw can handle.
What Is The Difference Between A Long Bar And A Short Bar?
If you have a short bar on your chainsaw, it means that the part of the saw furthest from the handle is not long enough to enable it to cut through wood. You need to replace this part with a longer one to make it longer.
Cons of longer bars
The negative consequences of putting a longer bar on your chainsaw are not worth the benefits. Here are the cons to a longer bar:
What Else To Change With The Bar?
There are a few things you can change with your bar to help optimize the performance of your saw. With that being said, the only thing you should change on the bar in length. Reducing diameter or adding thickness will not help improve the performance of your saw.
How To Make Your Chainsaw Bar?
If you want to make your bar, the first thing you need to do is find a metal that has the hardness that you desire. You’ll also need to find a strong piece of wood that measures 16 x 6 x 3/8 inches to make sure it’s long enough and strong enough.
Final Thought
There are many reasons why the bar is so important, but the main reason is that it makes the saw go and allows it to cut through wood like butter.
Why do chainsaws have a 40 bar?
To give an extreme example, putting a 40” bar on a 30 cc saw would make little sense, as the engine would not have ...
What is the maximum bar length for a saw engine?
saw engine size can be formed: for gasoline-powered saws, the maximum bar length in inches is 4/10 times the saw engine displacement in cc. This can be expressed mathematically as
How many cc can a chainsaw run?
A chainsaw can run 1 cm of bar length per 1 cc of cylinder displacement. In the table below, you can see what kind of maximum bar lengths this 4”/10cc rule produces for common engine sizes. Engine size. [cc] Max bar length. [in] [cm] 30 cc. 12”.
What is the rule for saw size?
Using the rule. The rule is intended to give you a rough idea of the bar length each saw size can typically run well . A few points: You can use the rule to roughly determine the max bar length for your saw in case you find no info from the saw manufacturer.
What is the limiting factor of bar length?
Power output is the main limiting factor of bar length. In gasoline-powered saws, power output correlates well with saw engine displacement (which is usually easier to find out). Engine displacement can therefore be used to determine the appropriate bar length. The main benefit of the engine size approach is that it is not specific ...
When will chainsaws be available in 2021?
January 17, 2021. Most chainsaws ship with a guide bar that is reasonably sized relative to the saw capacity, but could actually run a longer one. Swapping the original bar for a longer model is often useful, as it may give you just the bit of additional cutting capacity you need in felling or bucking. But how much longer a bar can you fit on your ...
Can a guide bar be used with a chainsaw?
In short, a guide bar is compatible with a certain chainsaw if it has two things: the same bar mount type and the same chain pitch as the saw. So before rushing to get the first long bar to go with your saw, please make sure it is actually compatible.
How big of a chainsaw can take a 20 inch bar?
For example, the Husqvarna 460 Rancher is commonly sold with a 20 inch bar and chain. However, it is capable of taking anything between 13” and 24”.
How big is a Husqvarna saw bar?
They come in a variety of sizes. Typically, most homeowner saws have bars which measure between 10 inches and 20 inches in length, although something like the Husqvarna Rancher 460 can take a 24-inch bar. As you would expect, professional saws are capable of handling even bigger units than this.
How many teeth does a chain saw have?
On chainsaws, the number of teeth on the sprocket varies and those with up to 10 teeth tend to have low kickback qualities. Models with 11 teeth or more have a higher kickback tendency but better cutting performance, though these tend not to be found on homeowner saws. Most homeowner saws have sprocket nose guide bars and whilst these offer better ...
What size sprocket do you need for a carving bar?
Some carving bars have. very narrow tips. These ‘dime’ tips need a ¼ inch sprocket to run the small chains which will go round the tip of the bar.
Why do chainsaws have a hard nose?
On a chainsaw, the sprocket is at the tip of the bar (hence the term nose sprocket) and is designed to reduce friction and therefore increase cutting performance. A hard nose does not have any wheel at its tip, and these are usually favored when working in gritty, difficult conditions and when cutting dirty wood which might jam the sprocket.
What is a narrow kerf bar?
What is a narrow-kerf bar? The kerf refers to the width of the bar and therefore the type of chain it can carry. As the name implies, a narrow kerf means it has a smaller width than the standard kerf unit. As the saw cuts, it creates a channel or groove and this is the kerf.
What size bar should I use for tree trimming?
In terms of size, bars between 8-in and 14-in are best used for trimming, pruning and light cutting. They are also good for small tree cutting and removing tree limbs. Sizes 16-in to 18-in are best for small tree cutting and removing tree limbs. They are also good for medium duty tree cutting and storm clean-up.
Can you Put a Long Bar on a Chain Saw?
The official answer to this question is NO, because of the design and construction of the chainsaw itself.
Why You Might Want to Put a Longer Bar on a Chainsaw
There are times when it is simply not possible to cut something from the ground with your normal saw because of the height of the object that needs cutting or because of strong winds that make things dangerous.
Different Types of Bar Designs for Different Chainsaws
Before you go out shopping for a longer bar, it is important to understand that they are designed differently depending on the type of saw you currently own.
Bar Lengths
Remember that a longer bar will not always give you more reach. It all depends on the angle at which you cut too. For example, if your tree branches are growing horizontally, a 10-inch bar may be too long for you to use because of the angle.
Chainsaw Maintenance Tips for Longer Bars
Even if you have bought the correct length of chain for your chainsaw using a longer bar, you will still need to keep your saw well maintained.
Benefits of Having an Extended Bar on Your Chainsaw
There are some definite benefits of having an extended bar on your chainsaws. These include:
Conclusion
Can you Put an Extended Bar on a Chainsaw? An important thing to keep in mind before we begin is that not all saws are suitable for extended bars. It all depends on the length of your bar and how well it fits onto your particular chainsaw model.
Bar Length Based on Chainsaw Power
- The biggest thing that affects the compatible length of chainsaw bars, is the engine power of the chainsaw. That’s what we’ll focus on in this section. If you’d like to learn about pitch, gauge, and other bar measurements (other than length), check out our comprehensive chainsaw bar guide. Generally speaking, the higher the power of a chainsaw, the longer the guide bar it can handle. C…
Find & Use The Manual: The Easy Way
- I know, user manuals sound incredibly boring. Don’t worry, I’ve got an approach that I use to find and auto-search chainsaw user manuals, that should make it relatively painless. But first, here’s why this is important. No matter how you look at it, chainsaws are dangerous machines. So it’s critical to get the details right, and to use appropriately fitting components. Safety first. Using th…
What Else to Change with The Bar?
- Before you change your guide bar, you will also want to consider the other chainsaw components this might impact. Specifically, a new guide bar may mean you also need 2 other components: 1. New chain 2. New sprocket If you increase (or decrease) the length of your bar, you will definitely need a new chain. This is pretty straight forward, if the bar gets longer, you’ll need a longer chai…
Wrap-Up
- If you find yourself wondering, “can I put a longer bar on my chainsaw?”, then you’re in good company. This is an age old question that’s been pondered by countless arborists, lumberjacks, and home improvement folks. The good news is, you can find the answer in a few simple steps: 1. Use the chart above to get a ball-park estimate 2. Check the user...