Receiving Helpdesk

beko washing machine test mode

by Prof. Mireille Bosco Jr. Published 3 years ago Updated 3 years ago

Test Mode Sequence

  • 1: All the the display or led’s will flash to check that they are working and door will now be locked.
  • 2: Drum does a clockwise rotation.
  • 3: Drum rotates anticlockwise rotation
  • 4: Goes into spin mode on clockwise rotation make sure there are no clothes in machine before performing this test as washer will spin at its fastest rpm.

More items...

Part of a video titled Beko wmb 7, 8, 9 Series washing machines diagnostic & test ...
0:04
3:56
So we'll just do it again press the start button turn the machine on with the dial set to the 12 o'MoreSo we'll just do it again press the start button turn the machine on with the dial set to the 12 o'clock position. You will either now see an error code or a number will be displayed.

Full Answer

How to use Beko washing machine diagnostic mode?

When looking at the dial on a Beko washing machine treat it as a clock 1 to 12 as in picture. On some models you may have more programs but for the basic access into the diagnostic mode is the same the same. Start by turning the washing machine of with door shut.

How does the Beko washing machine fill cycle work?

10 th this will start fill cycle until water activates the pressure switch at normal fill level (Normally just below the glass on the door) when the Beko washing machine has reached the level it will start clockwise rotation at normal wash action and heat the water. Please note You Have to stop it manually.

How do I enter test mode on my washing machine?

To enter test mode. It is advisable that washing machine be switched off or at least 5 minutes prior to entering test mode With the machine switched off shut the door and turn the dial to the 12 o'clock position.

How do I get my washing machine back to normal mode?

Press again and you are back at the start. Turn machine of and leave for a few minutes and the switch back on and you’re in normal wash mode.

Can I reset my Beko washing machine?

If your Beko washing machine won't start, there's an easy reset process to follow: Locate the start, pause and cancel buttons. Press them all down at the same time for around 3-5 seconds. Your machine should now be reset.

How do you troubleshoot a Beko washing machine?

If your washing machine doesn't start, hold the start, pause and cancel buttons down for about three to four seconds. This should reset the machine and allow you to continue. If it does not work you may have to call out an engineer.

How do I find my Beko error code?

The Beko error code system is very simple it goes from E1 to E18, if you can correct the error yourself then you'll simply need to hold down the start button to clear the error code. Remember though if you can't correct the error or aren't confident enough to attempt it then we can help!

Why is my Beko washing machine not spinning or draining?

The most probable cause is a clogged pump filter. The pump filter should be cleaned every three months or when it's clogged. This filter is installed to catch foreign objects like buttons or coins, and to prevent these items from entering the drain hose.

How do you diagnose a washing machine problem?

Washer Troubleshooting GuideCheck that the washer is plugged in securely.Check the circuit breaker or fuse box.Test the outlet for current.Check that the water supply valves are turned on.Inspect the filter screens.Test for overheating.Test the water level switch.Test the timer control.More items...

How do I reset my washing machine?

1:243:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.

Where is reset button on Beko washing machine?

Try resetting the appliance by pressing and holding the start/pause/cancel button for three seconds.

Why is my Beko washing machine flashing?

The fabric softener/conditioner light on my Beko washing machine is flashing. This happens if the selector dial is turned during a programme. To stop the fabric softener light on your Beko washing machine from flashing, turn the selector dial back to the original programme.

How do you drain a Beko washing machine?

1:193:37Beko washing machine full of water? Check filter: How to! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd there's a little hose in here that you can pull out and that will drain the water into a bowl orMoreAnd there's a little hose in here that you can pull out and that will drain the water into a bowl or something. It's easier than putting down a load of blankets.

What causes a washing machine not to drain and spin?

If the washer won't drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.

How do you fix a Beko washing machine that won't spin?

0:3514:10Beko washing machine not spinning or turning how to replace carbon ...YouTubeStart of suggested clipEnd of suggested clipMight not be a motor fault it might be just a simple blockage in the system. This can either be onMoreMight not be a motor fault it might be just a simple blockage in the system. This can either be on the pump area and sometimes this can be on where the waste hose is fitted.

What to do if the washing machine is not draining?

What to Do When Your Washing Machine Won't DrainPerform a Master Reset. Unplug your washer for about one minute. ... Test the Lid Switch Assembly. ... See if the Drain Hose is Kinked. ... Check the Drain Hose or Pump for Clogs. ... Clean out the Coin Trap. ... Check the Water Level Control. ... Schedule Washing Machine Repair.

Beko WM5100S & WM5100W

Before entering test mode please be aware that you are not meant to leave the machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:

Test Mode Sequence

it is advisable that machine be switched off or at least 5 minutes prior to entering test mode

To exit the test mode

Turn the machine off wait a couple of minutes, when you turn the machine back on it should be set on a normal spin cycle.

What are the parameters of a washing machine?

2. Roller capacity. One of the most important parameters of a washing machine is the drum capacity, which indicates how many kilograms o. Continue Reading. 1. The first question to answer first is whether you need a drum washing machine or a pulsator washing machine.

Why is the number issued by the manufacturer not the actual capacity of the washing machine?

Usually, the number issued by the manufacturer does not represent the actual capacity, because it is difficult to determine from the perspective of the manufacturer measuring the lift or kilogram of the washing machine. Therefore, choose a little less than the specifications listed by the manufacturer. 3. Speed.

How many kgs of clothes can a washing machine wash?

The average laundry capacity is about 7 kg.

Does the number on a washing machine represent the actual capacity?

Of course, it depends on how often you take a shower. Usually, the number issued by the manufacturer does not represent the actual capacity, because it is difficult to determine from the perspective of the manufacturer measuring the lift or kilogram of the washing machine.

Can a smart washing machine be programmed with a laundry app?

Some washing machines also offer a reservation function that allows you to set up the machine at a specific time. Some smart washing machines can even be programmed with a laundry app so you can not only delay the start, but also stop the loop. 8. Other useful features.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9