If your Beko washing machine is not filling with water or stopping in the cycle then it you may have a water fill problem. You may be getting Beko error code E08. The problem may be one of these. Faulty tap going to washing machine. Kinked water pipe.
Full Answer
How to fix a washing machine that won’t fill with water?
Replace them carefully and tighten the nuts by hand. If your washing machine detects that its door is open, it won’t fill with water. Make sure that the door is firmly closed. Remove items that get caught in the door and shut it until you hear a locking sound. If the problem continues, your washing machine might have a technical problem.
Can you fix a washing machine with no error code?
Please do not take any action unless you are confident you can do it safely and legally, it’s always better to call a professionsl Repair Aid engineer than go it alone. But if you have an older model of washing machine or no error code is being displayed then don’t worry you may still be able to fix the problem.
How do I know if my washing machine interlock is bad?
If you suspect your interlock to be at fault, it needs to be tested with a multimeter for electrical continuity. The results will show whether the detail should be replaced or if there is something else that’s interfering with the proper filling of your washing machine.
How do I know if my washing machine selector switch is bad?
To test if your selector switch is damaged or worn out, you need to check the solenoids for continuity. Refer to the wiring schematic of your washing machine model to locate the selector switch wire connections that power the water inlet valve. Using a multimeter, test the terminals for continuity.
Why is my Beko washer not filling with water?
If this happens, check that the water hose at the back of the appliance is not twisted or being crushed by anything and the water to the machine is turned on. If this does not solve the problem, you may need an engineer.
Why is my washing machine not filling with water?
0:187:25Washer Won't fill? - Top 5 Problems and Fixes - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne is located in the end of the fill hose. And the other is inside the inlet valve itself if theMoreOne is located in the end of the fill hose. And the other is inside the inlet valve itself if the washer won't fill it could be that the screens are clogged. So take your fill hoses.
How do I get my washing machine to fill with water?
Check that the lid is completely closed.Make sure the hot and cold water supplies are on.See if the fill hoses are kinked.Check if the water inlet screens are clogged. To do this, you must first turn off the water. Then remove the fill hoses and clean the screens.
How do you test a washing machine water inlet valve?
1:552:50Washer Not Filling? Water Inlet Valve Testing, Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipDisconnect the hot and cold water supply lines from the inlet valve and hold them over a bucket or aMoreDisconnect the hot and cold water supply lines from the inlet valve and hold them over a bucket or a washtub.
1. Washer Not Draining
Beko washers can be difficult to drain. Usually, this is not a problem because the lint trap will catch the majority of the lint. However, if there is a clog in the drain hose, it can prevent the water from draining completely.
2. Beko Washer Leaking Water
This is the most common problem with Beko washers. It happens because the rubber O-rings inside the tub (the part that holds the wash water) get soft after years of use and eventually lose their seal against the inner sides of the tub.
4. Beko Washing Machine Stuck Cycle
This problem occurs when the machine gets into a state where it won’t start a cycle until you use a key or other external force. There are several possible causes:
5. Washer Runs Too Fast
First, check to see that the washer is plugged in and that the fuses in the circuit where the washer is located are not blown.
6. Beko Washer Noise
Noise is a common problem with many washing machines. Some of the causes of noise include:
8. The machine is not filling with water
Most probably you are using the wrong amount of water. Either too much or not enough.
Why is my washing machine not filling with water?
If you’re lucky then your washing machine not filling with water could all be caused by a simple kink in your hose. This is a much more common issue than many people realise and is thankfully easy to fix, simply unkink the hose.
Why is my washer not filling with water?
Water Valves. If you are getting a flow of water through your hose but your washer is still not filling with water then the problem could be with your water valve. If you’re lucky the issue might simply be that the filter needs cleaning, be careful with your water valve filter though because many of them are very fragile.
Why is my hot water hose not coming through?
If your hose isn’t kinked or damaged but water is still not coming through then the problem could be with the pumping taps. The pumping tap s can sometimes get clogged with dirt preventing a flow of water through the hose, this is a more common issue with the hot water tap.