If your Beko washing machine will not switch on, there could be an electrical fault. Here’s how to test for that: Do not plug your washing machine into an extension socket, only ever plug your washing machine into a mains wall socket. Test that the power socket is working by plugging in something you know is working, a light for example.
Full Answer
What are the common faults of the Beko washing machine?
5 Beko washing machine common faults (with simple solutions) 1 1. Beko washing machine not draining. If the water is not draining out of your machine, you may have a problem with your: 2 2. Beko washing machine not spinning. 3 3. Your machine won't start. 4 4. Beko washing machine stuck on cycle. 5 5. The door won't open.
How to enter test mode in Beko washing machine?
How to enter test mode Beko washing machine to find the fault Start by turning the washing machine of with door shut. Now turn the dial to the position 1 Which is normally the 90c hold the start /pause button down while you press the on/off button to on for a couple of seconds till light flashes
How do I know if my Beko washing machine is leaking water?
Measure the water flow rate. At least one litre in seven seconds is required. If the flow rate is less, you need a plumber to check your water line. If your Beko washing machine’s water inlet hose has become kinked or twisted it may results in not enough water getting into the drum.
What does error code E11 mean on a Beko washing machine?
E11 – Beko washing machine error code E11 points to a motor error detection. Repairing or replacing this part is more complicated and needs the intervention of an experienced technician.
How do you run diagnostics on a Beko washing machine?
0:043:56Beko wmb 7, 8, 9 Series washing machines diagnostic & test modeYouTubeStart of suggested clipEnd of suggested clipSo we'll just do it again press the start button turn the machine on with the dial set to the 12 o'MoreSo we'll just do it again press the start button turn the machine on with the dial set to the 12 o'clock position. You will either now see an error code or a number will be displayed.
How do you troubleshoot a Beko washing machine?
If your washing machine doesn't start, hold the start, pause and cancel buttons down for about three to four seconds. This should reset the machine and allow you to continue. If it does not work you may have to call out an engineer.
How do you reset a Beko washing machine?
If your Beko washing machine won't start, there's an easy reset process to follow:Locate the start, pause and cancel buttons.Press them all down at the same time for around 3-5 seconds.Your machine should now be reset.
How do you diagnose a washing machine problem?
Washer Troubleshooting GuideCheck that the washer is plugged in securely.Check the circuit breaker or fuse box.Test the outlet for current.Check that the water supply valves are turned on.Inspect the filter screens.Test for overheating.Test the water level switch.Test the timer control.More items...
What are common problems with washing machines?
10 Most Common Washing Machine ProblemsIt Bounces Around. ... It's Noisy. ... Clothes Are Getting Ripped. ... Improper Or Slow Draining. ... My Washing Machine Won't Spin. ... There's No Water. ... The Door Won't Open. ... It's Smelly.More items...
Why washing machine suddenly stopped working?
There are a few possible reasons for this: - The locking mechanism could have jammed (maybe some clothes have gotten in the way). - There could be a glitch in the washer's computer. - The washing machine may not be draining properly, leaving the washer door locked and the drum filled with water.
How do I find my Beko error code?
The Beko error code system is very simple it goes from E1 to E18, if you can correct the error yourself then you'll simply need to hold down the start button to clear the error code. Remember though if you can't correct the error or aren't confident enough to attempt it then we can help!
Where is reset button on Beko washing machine?
Try resetting the appliance by pressing and holding the start/pause/cancel button for three seconds.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.
How many years should a washing machine last?
around 10 yearsWashing machines, on average, last around 10 years, according to Consumer Reports.
How do I reset my washing machine?
1:173:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
How do you reset the circuit board on a washing machine?
Reset your washing machine There really isn't a way to reset the washing machine. What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again.
Why won't my Beko washing machine open?
If your Beko washing machine door won't open, you potentially have a very messy problem on your hands. The first thing you'll need to do is make sure that your machine isn't still full of water:
Why is my Beko washing machine not spinning?
Beko washing machine not spinning. A non-mechanical problem which might be affecting your machine's ability to spin might be the type and size of load you've placed inside it. Try not to overload or chronically underload your machine.
How to clean a blocked water filter?
Be aware though that when you open the housing there may be water inside. You can drain the water out using a tube, put a container down to catch it and/or get a bunch of towels ready. Rinse the filter and replace it.
What is a fault in a pressure switch?
Faulty pressure switch: there is a pressure switch inside which tells the machine when the cycle is over. If this is malfunctioning, unplugging your machine from the wall for 10 minutes should fix your problem. This will reset it properly. Faulty interlock: if that doesn't help, your interlock may be at fault.
What is non-necessary cookie?
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
What to do if the "on again off again" approach doesn't work?
If the simple “on again off again” approach doesn't work, you'll probably need an engineer. Otherwise, you'll be left trying to wedge or wangle the door open, which is an easy way to break it.
Is a washing machine a modern convenience?
Washing machines are amazing modern conveniences. But they're not immune to faults and malfunctions...
1. Washer Not Draining
Beko washers can be difficult to drain. Usually, this is not a problem because the lint trap will catch the majority of the lint. However, if there is a clog in the drain hose, it can prevent the water from draining completely.
2. Beko Washer Leaking Water
This is the most common problem with Beko washers. It happens because the rubber O-rings inside the tub (the part that holds the wash water) get soft after years of use and eventually lose their seal against the inner sides of the tub.
4. Beko Washing Machine Stuck Cycle
This problem occurs when the machine gets into a state where it won’t start a cycle until you use a key or other external force. There are several possible causes:
5. Washer Runs Too Fast
First, check to see that the washer is plugged in and that the fuses in the circuit where the washer is located are not blown.
6. Beko Washer Noise
Noise is a common problem with many washing machines. Some of the causes of noise include:
8. The machine is not filling with water
Most probably you are using the wrong amount of water. Either too much or not enough.
How to check if Beko washing machine is child locked?
If your Beko washing machine will turn on but you can’t use any of the buttons, here’s how to check if childlock is on: If your washing machine has a digital display it will tell you that childlock is on when you press any button by displaying C ON. To turn off the childlock function, press and hold the button or two buttons indicated with ...
Why won't my Beko washing machine turn on?
If your Beko washing machine will not switch on, there could be an electrical fault. Here’s how to test that: Do not plug your washing machine into an extension socket, only ever plug your washing machine into a mains wall socket. Test that the power socket is working by plugging in something you know is working, a light for example.
Why is my Beko washing machine not getting water?
If your Beko washing machine’s water inlet hose has become kinked or twisted it may results in not enough water getting into the drum. To check if this is a problem:
How to make sure washer hose is not leaking?
Make sure that the connector on either end of the hose are securely fastened to the mains water and your washing machine and that they are not leaking.
Why is my washing machine running so long?
If the supply of water to your washing machine is too weak, this may cause issues such as extended cycle times. To test that your water supply is strong enough:
What is a Beko manual?
Beko manuals contain helpful information and advice about your appliance.
What to do if your washing machine won't turn on?
If your washing machine does not turn on when connected to the power, replace the 13amp fuse in the plug. If the issue is still not resolved there may be an electrical fault.
How to check if washer is working?
1: All the the display or led’s will flash to check that they are working and door will now be locked. 2: Drum does a clockwise rotation. 4: Goes into spin mode on clockwise rotation make sure there are no clothes in machine before performing this test as washer will spin at its fastest rpm.
How to test a washing machine?
It is advisable that washing machine be switched off or at least 5 minutes prior to entering test mode. With the machine switched off shut the door and turn the dial to the 12 o'clock position. Now press and hold down the start/pause button and press the on/off on, while holding the start/pause button down for 3 seconds ...
How long to turn off washing machine before test mode?
To enter test mode. It is advisable that washing machine be switched off or at least 5 minutes prior to entering test mode. With the machine switched off shut the door and turn the dial to the 12 o'clock position.
Can you leave a washing machine unattended?
Before entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:
How to reset a Beko washing machine?
Your Beko washing machine does not start. If your washing machine doesn’t start, hold the start, pause and cancel buttons down for about three to four seconds. This should reset the machine and allow you to continue. If it does not work you may have to call out an engineer.
Why isn't my washing machine rinsing?
The machine isn’t rinsing properly. This is normally because the drain pump filter is blocked. Open the cover of the filter on the bottom right side of the machine, careful to collect the water. Open the filter housing carefully to stop water from flooding out and then clean it under the tap.
Why is my washing machine not filling with water?
The machine is not filling with water. The main reason this occurs is if the hose is twisted or blocked in some way. Pull the machine out and make sure there is no problem with the hose. If this doesn’t fix the issue, you will need to call out an engineer.
Why is my spinning machine not spinning?
The machine is not spinning. If the load in your machine is not distributed properly it can affect the spinning function. This occurs if you have a mix of items in the drum including heavy towels and woollen jumpers as well as lighter items like underwear. This imbalance stops the spin cycle from getting to full speed.
How long does it take to wash a Beko washing machine?
Daily Quick programmes can wash a full load in just 28 minutes, and innovative steam settings reduce creases and saves on ironing.
What is the E8 code on a Beko washing machine?
E8 – Beko washing machine error code E08 is linked to the appliance not filling with water. This could be caused by a defective water valve, faulty antiflooding mechanism, wiring issues, and many other potential component failings.