How do you calculate the price of asphalt?
Why Does Asphalt Crack?
- The Sun. The sun is one of asphalt’s worst enemies. ...
- Moisture. Moisture beneath the surface of the asphalt causes the gravel base to shift. ...
- Ground Movement. In addition to the ground movement caused by moisture, temperature changes also create movement. ...
What is the average cost for hot asphalt per ton?
What Is The Average Cost For Hot Asphalt Per Ton? Hot mix asphalt costs $100 to $200 per ton. This is the standard type for all-weather surfacing and repairs. Cold mix asphalt costs $10 to $50 per bag, but you can only use it for temporary repairs. How many tons of asphalt are in a dump truck? How much can you deliver in one truck
How much for a ton of asphalt?
How Much Does Asphalt Cost Per Ton? The asphalt is sold in a bulk system. The minimum amount is one ton. The cost of asphalt per ton is on average, around 70 to 80 dollars in the current market. The amount depends on the manufacturing cost. So, it may vary from time to time and place to place.
Is asphalt cheaper than concrete?
There are a few reasons asphalt is cheaper than concrete. One is due to the costs of the materials required to make asphalt. Also, asphalt is easier and quicker to install. Concrete also has many finishing options that can make it much more expensive. Asphalt is commonly referred to as blacktop or pavement.
How many tons of asphalt are in a truck load?
Super Dumps are capable of hauling payloads from 19 to 26 tons, if you can properly distribute the loads to each axle. A typical tandem dump truck is limited to about a 13-ton payload in accordance with federal bridge law. Increased truck capacity is important when directly unloading into the asphalt paver.
How is asphalt sold?
Asphalt is usually sold by the tonne from companies specializing in construction, usually road construction and roof water-proofing. Our hot mix asphalt calculator will help you estimate how much of it you need, approximately.
How much does black top cost?
Type of Driveway Material Cost Per Square FootDriveway Material Cost Per Square Foot EstimateAsphalt/Blacktop$7 - $13Gravel$1 - $3Chip Seal$2 - $5Heated$12 - $216 more rows•Mar 29, 2022
How do you calculate asphalt cost?
Asphalt is usually priced by square foot. The cost per ton is $40 to $80 and per square foot is $0.75 to $2.00. The cost is determined by the size of rock in the asphalt, volume ordered, delivery cost, and the location of the work being performed.
How many yards of asphalt are in a ton?
There are approximately 0.5 cubic yards in a ton of asphalt. 1 cubic yard of asphalt weighs around 4,050 pounds and 1 ton of asphalt weighs about 2,000 pounds, so, number of yards of asphalt in a ton = 2000 ÷ 4050 = 0.5 yards approx. Thus, there are 0.5 cubic yards in one ton of asphalt.
What does 1 ton of asphalt weigh?
According to Asphalt Institute, 2,000 pounds equals 1 ton. Continuing the example, the pound value will be divided by 2,000 to determine the amount in tons: 5,920 pounds of asphalt mix/2,000 = 2.96 tons.
Is asphalt the same as blacktop?
Blacktop is heated to approximately 150 degrees celsius, whereas asphalt is only heated to 120 degrees celsius. Asphalt is has a higher bitumen content and for that reason is less porous and more resilient to wear and tear from high traffic and thus is the preferred choice for major highways.
Is blacktop cheaper than concrete?
The cost of an asphalt driveway is typically cheaper than concrete, costing $2.00 – $4.00 per square foot. Asphalt prices tend to fluctuate with fluctuations in crude oil prices. In contrast, a concrete driveway costs between $4.00 – $6.00 per square foot for a standard installation.
How wide should a driveway be?
Primarily, most professionals recommend that you install a 10 feet to 12 feet wide driveway. The standard driveway width for an SUV or conventional pickup truck is 10 feet. Anything less than 10' wide will likely present difficulties for drivers, even in smaller vehicles.
How thick should a asphalt driveway be?
2 to 3 inchesResidential driveways typically use 2 to 3 inches of asphalt with 3 being suitable for occasional large trucks or heavy equipment. Underneath the asphalt you should have 6 to 8 inches of granular base aggregate.
What is the asphalt price index?
2022 State IndexesStateJanFebCalifornia$404.70$460.70Colorado$436.23$526.01Connecticut$512.50$522.50Delaware$545.00$566.6742 more rows
How do you quote an asphalt driveway?
Amount of asphalt: consider the length, depth, and width of your driveway. Then ask your contractor to check and provide you a quote. Transportation costs: the farther your house is located, the more you are likely to pay more costs. This will also affect the type of asphalt you will use such as warm or hot mixes.
Why seal a crack in a driveway?
Sealing too often creates sealer cracks. Sealing prevents condensation between the asphalt and air and keeps the asphalt more moist.
Is a low RAP mix driveway more expensive?
A driveway design with low RAP mix is generally more expensive . You will generally pay more for a company with a good reputation. Smaller paving contractors cut costs by operating older equipment. Large paving contractors generally have higher labor costs.
How Much Does an Asphalt Driveway Cost?
The average cost for an asphalt driveway is $4,996, but that will vary depending on several factors, including the size of your driveway, how deep of a layer of asphalt you want for your driveway, and even the type of asphalt.
Cost Estimator by Driveway Size
The size of your driveway is the biggest factor in determining the cost of your asphalt driveway. Expect to be charged at least $3,258 for an average-sized driveway at an average price. Sometimes the costs of labor will be added, sometimes they are included. Here we’ll break down the costs by square foot, ton, and labor hours.
Other Factors Affecting Cost
Your final bill for your asphalt driveway is going to depend on a lot of factors, including the depth of your asphalt layer, any decorative (stamped asphalt) or extraordinary (heated driveway) features, and the cost of substrate.
Services Often Bundled With Asphalt Driveways
Other outdoor services are often bundled with the installation of an asphalt driveway. Most of these additional services (tree removal or land grading, for example) involve preparing the land for your driveway.
Costs of a DIY Asphalt Driveway
You may be tempted to install your own asphalt driveway. Resist the temptation. This is going to be an enormous project. But if you think you’d like to DIY your asphalt driveway, we’ll outline the pros and cons as well as costs and materials required.
Conclusion
An asphalt driveway will cost you anywhere from $3,086 to $7,912, with an average cost of $4,996. Note that the price of any add-on services will increase your final bill.
About Us
LawnStarter is a startup making lawn care easy affordable and reliable. Follow this blog to stay tuned with what you need to keep your lawn in tip-top shape year-round.
How much does it cost to recycle asphalt?
A recycled asphalt driveway costs $2 to $5 per square foot installed or from $0.15 to $0.40 per square foot for materials only. A ton of asphalt millings covers 60 square feet on average, while a cubic yard covers 80 square feet at 4" deep.
How much does asphalt milling cost?
Asphalt millings can and should be sealed to make pavement last longer. Asphalt sealing costs $0.20 to $0.70 per square foot, depending on the cleaning and prep work required. Hire a professional paver to choose the most-suitable asphalt millings sealer and application method.
How much does recycled asphalt weigh?
Recycled asphalt weighs 90 to 120 pounds per cubic foot or between 1.2 and 1.6 tons per cubic yard, depending on the quality and mix composition. Asphalt millings typically weigh less than new hot-mix asphalt. Rain makes recycled asphalt millings heavier by raising its moisture content.
How long does it take for recycled asphalt to harden?
After steamroller compaction and sealing, the recycled asphalt millings take 24 to 48 hours to harden. First, the steamroller will compress and heat the millings that bind together to create a hardened level surface. Then pavers spread a sealant on top to stabilize the blacktop.
What is asphalt milling?
Asphalt millings are old recycled asphalt pieces crushed into a smaller gravel-size rock. Contractors compact and seal the crushed asphalt to create driveways, roads, parking spots, sidewalks, or blacktops. Asphalt-recycling facilities heat reclaimed millings to remove impurities and excess moisture.
How much asphalt do I need for a tennis court?
How much recycled asphalt do I need for a basketball or tennis court? Recycled asphalt for a 94x50-foot basketball court costs $700 to $1,800 and requires 70 to 90 tons of asphalt millings. A 78x36-foot tennis court requires 40 to 55 tons of recycled asphalt that costs $400 to $1,100 on average. Return to Top.
How thick is asphalt for a truck?
Driveways for heavy trucks need 5+ inches of asphalt millings. Small, lightweight vehicles require a layer 3 to 4 inches thick.