Full Answer
How much does asphalt cost per square foot?
Asphalt cost per ton One ton of asphalt covers 30 to 80 square feet. How much does a blacktop driveway cost? Paving an asphalt driveway costs $4,737 on average, with a range between $2,932 and $6,568. This project runs $7 to $13 per square foot, including $2 to $6 per square foot for materials and $5 to $7 per square foot for labor.
How to calculate asphalt/hot mix driveway cost?
17/12/2020 · Asphalt cost per square foot. Asphalt costs $0.75 to $2.00 per square foot when spread 3" to 5" thick. A ton of asphalt covers 30 to 80 square feet. An average 2-car driveway requires 10 to 18 tons of asphalt, costing $600 to $1,100 for asphalt materials or $1,700 to $4,000 including installation.
How much does it cost to pave a 2 car driveway?
07/04/2016 · Rip and trim existing base compact ready for asphalt 500m2 about $3,500 plus GST. Full box out remove 180mm of soil supply spread 150mm of road base compact and trim ready for asphalt 50m2 about $2,000 plus GST. Rip and trim existing limestone compact and ready for asphalt 7,000m2 about $49,000 plus GST
How much does a bulk truckload of asphalt cost?
Asphalt Driveways Cost: based on 200m2, 1hr from depot. PREPARATION: - Weed treatment - Excavation and sub grade preparation - Supply and compact base to 100mm thick: $15 to $20pm2 ASPHALT LAYING: - 7mm thick Primerseal and 30mm thick Asphalt: $40 pm2
How do you calculate asphalt cost?
To determine the total asphalt cost for your project, all you need to do is to multiply the total asphalt weight required by the cost per weight of the asphalt you are purchasing.15-Dec-2021
How many square meters is a ton of asphalt?
24 SqMOne ton of asphalt covers: 2” or 50.8 mm thick = 24 SqM.
How do I calculate an asphalt driveway?
0:322:12How To Quickly Figure The Cost Of An Asphalt Driveway - YouTubeYouTubeStart of suggested clipEnd of suggested clipOut this driveway here on this example measures 20 feet by 30 feet. So all you have to do is toMoreOut this driveway here on this example measures 20 feet by 30 feet. So all you have to do is to multiply. 20 by 30 and that's going to give you the square footage of this driveway.
How many m2 are in a m3?
one square meterOne cubic meter is equal to one square meter.
What does 1 ton of asphalt weigh?
According to Asphalt Institute, 2,000 pounds equals 1 ton. Continuing the example, the pound value will be divided by 2,000 to determine the amount in tons: 5,920 pounds of asphalt mix/2,000 = 2.96 tons.
Is 2 inches of asphalt enough for a driveway?
Residential driveways typically use 2 to 3 inches of asphalt with 3 being suitable for occasional large trucks or heavy equipment. Underneath the asphalt you should have 6 to 8 inches of granular base aggregate. Underneath this you have soil.25-Feb-2019
How much does it cost to pave a driveway calculator?
Cost to Pave a DrivewayDriveway Paving Cost CalculatorZip CodeBasicBestInstallation Cost$1250.00 - $1275.00$2250.00 - $2900.00Total$1625.00 - $1712.50$2800.00 - $3550.00Total Average Cost per square foot$6.67$12.701 more row
Can you put asphalt over concrete?
It is safe to pave asphalt over concrete. Concrete is a great base material because it is stable and allows for excellent compaction of the asphalt above. In fact, many miles of concrete roads are paved over with asphalt every year.24-Jun-2014
How much does asphalt cost per ton?
Asphalt cost per ton. Asphalt costs $40 to $80 per ton on average. Asphalt prices vary depending on the mix and material ingredients. One ton of asphalt covers 30 to 80 square feet. A 2-car driveway needs 7.5 to 18 tons of asphalt, depending on the thickness. Asphalt cost per ton by material - chart.
How many tons of asphalt is in a cubic yard?
There are typically 2 tons in 1 cubic yard, depending on the mixture's density. A cubic yard covers 65 to 110 square feet with an asphalt layer 3 to 5 inches deep.
How much asphalt does a tandem truck carry?
Tandem trucks carry 13 to 20 tons of asphalt that cover 550 to 850 square feet with a layer 3 to 5 inches thick. Prices vary according to the asphalt-delivery distance. Bulk asphalt cost per truckload - chart.
What is the most important thing to consider when installing a new driveway?
The most important and often under valued item to be considered when installing a new driveway is the road base and compaction. . Without a good road base, ASPHALT, BITUMEN can crack, split and turn into potholes within a few months or in extreme cases, it may even start cracking or sinking as your contractor is rolling it.
When to use primerseal?
Primerseals are an absolute must when asphalting steep driveways as asphalt will shove and crack when being rolled due to the lateral forces of the machinery. The aggregate in the primerseal is rolled throught the bitumen and keys into the base.
Is it better to have a road base free draining or free draining?
Without water during the compaction process the road base will not compact, roller lines and tyre marks will remain no matter how many times you go over it. The road base should be shaped to be free draining where possible. A free draining surface is far better than installing drainage and is also less expensive.
What is prime kerosine?
Prime is a blend of kerosine mixed 50-50 with bitumen to give you a very liquid material that will penatrate and bind together the top layer of the base. Different blends of prime and application rates are suited to different sites and road base but on most sites it is laid at 0.8 Litres per m2.
Is it better to install free draining or prime?
A free draining surface is far better than installing drainage and is also less expensive. The next step is to apply: Primerseal if you have decided to lay asphalt and: Prime if you are going to lay bitumen or coloured bitumen.
What is prime asphalt?
Prime is ideal for sealing and stabalizing the top layer of loose or porus road base. The final step is laying the Bitmen or Asphalt. Asphalt must be laid to a compacted minimum thickness of at least 20mm, anything less and it WILL fail.
Is machine laid asphalt better than hand laid asphalt?
Machine laid asphlat is far better than hand laid so make sure you ask you contractor if a asphalt paver will be used. Machine laid asphalt is smoother and denser and will last years longer than hand laid asphalt, the asphalt paver partially compacts the hot asphalt prior to it being rolled.
Enter the dimentions of the area to pave
You can calculate Asphalt / Hot Mix driveway cost and material estimate using our Hot Mix Asphalt Tonnage Calculator.
DISCLAIMER
Actual densities may vary depending on the components of the mix and also vary somewhat between different mixes. But this value is for estimating standard. The tonnage calculation is specific to Asphalt only.
Is asphalt driveway good?
It’s easy to see why asphalt driveways are popular. They’re reasonably cheap and quick to lay and offer a smooth, uniform appearance. And if properly installed, an asphalt driveway is low maintenance and very durable. Asphalt and tarmac are often used interchangeably, but there is a difference.
Can you overlay an existing driveway?
It can cost more if you’re installing an irregular shaped or very large driveway. But if you’re only overlaying an existing asphalt driveway, you can expect the price to be cheaper. Because of the specialist plans and skill required, a lot of the cost is due to deliveries and having a particularly skilled gang on site.
Can you use a manhole cover on a new driveway?
Re-using an old gully or manhole cover can often take the shine off a new drive. Ensure that your driveway contractor uses the correct loading on any manhole covers, particularly if your drive has heavy vehicles on it at any point.
Is stamped asphalt the same as asphalt?
Stamped asphalt offers all the same benefits as standard asphalt, like durability and low maintenance. But it also has the added bonus of a greater decorative appeal. It can mimic the effect of more expensive driveway options, such as block paving.
Is it cheaper to install asphalt over a new driveway?
This means a new layer of asphalt will be installed over the top. It can be considerably cheaper than having a new driveway installed. This is because all the excavation and foundation work has already been done when the first driveway was installed.
Asphalt calculator formula
Based on the measurements you provide for required length, width and thickness, the calculator first works out the area and volume of the hot asphalt mix required using the below formulas:
Calculation examples
Imagine I want to pave over an area measuring 20 feet by 4 feet to a thickness of 6 inches using standard asphalt (140 lb/ft³) and costing $150 per US short ton.
What if my measurements are in different units?
The best thing about our asphalt calculator is that it takes care of this for you.