What is the minimum distance from Table B for TJI joists?
TJI Joists Minimum distance from Table B 1½" round holes may be cut anywhere in web outside of hatched zone if they are located 3" away horizontally (edge-to-edge) from a larger hole. 2 x D 1 minimum (applies to all holes except knockouts) Closely grouped round holes are
What are the allowable holes for Trus Joist products (poster)?
Allowable Holes for Trus Joist Products (Poster) Trus Joist TJI Joists Minimum distance from Table B 1½" round holes may be cut anywhere in web outside of hatched zone if they are located 3" away horizontally (edge-to-edge) from a larger hole. 2 x D
How do I determine the hole size for a TJI joist?
Table A, Table B, or both if required, determine the hole shape/size and select the TJI joist and depth. 2. Scan horizontally until you intersect the correct hole size column. 3. Measurement shown is minimum distance from edge of hole to support. 4. Maintain the required minimum distance from the end and
How to use tables a and B when scanning for TJI joists?
Minimum distance from edge of hole to inside face of nearest intermediate or cantilever support How to Use Tables A and B 1. Using Table A, Table B, or both if required, determine the hole shape/size and select the TJI joist and depth. 2. Scan horizontally until you intersect the correct hole size column.
How many holes can I drill in floor joists?
You can drill the holes anywhere along the length of the joist (first photo). If you have manufactured I-joists, you can drill holes up to 1-1/2 in. diameter almost anywhere in the web area (the area between the flanges). Just stay 6 in.
How big a hole Can I drill in a joist?
The hole cannot be larger than one-third the depth of the joist, so the maximum hole size for a 2×12 joist (actual size 1-1/2 x 11-1/4 in.) is 3-3/4 in. diameter—plenty big enough for running cable! You can drill the holes anywhere along the length of the joist (first photo).
How big of a hole can you drill in a 2x8 floor joist?
You can put holes in floor joists anywhere along the length of the joist, but you can't put them any closer than 2″ from the top or bottom edge of a joist. The maximum size of a hole is 1/3 the depth of the floor joist.
How big of a hole can you drill in a TJI floor joist?
The maximum allowable hole is 6 ½” diameter in a 16” deep TJI® joist.
What is code for drilling holes in floor joists?
IBC 2308.8. Notches on the ends of joists shall not exceed one-fourth the joist depth. Holes bored in joists shall not be within 2 inches (51 mm) of the top or bottom of the joist, and the diameter of any such hole shall not exceed one-third the depth of the joist.
What size hole Can I drill in a 2x10 floor joist?
The maximum allowable diameter of a hole in any solid-lumber joist is one-third of the joist's depth. Notches can't be deeper than one-sixth of the joist depth. In the case of your 2×10 joists, the maximum diameter is 35⁄64 in.
Can you drill a 3 inch hole in a 2x10 floor joist?
Simply following building code, you'll only be allowed to bore a 3-5/64" hole through a 2x10 joist. A 2x10 is actually only 9-1/4" deep, and building codes set the maximum hole size to 1/3 the depth of the member (9-1/4" / 3 = 3.08333").
What are the requirements for holes and notches in joists?
Notches can only be made in the top OR bottom of the joists, (not both) within the permitted area to a maximum of 35mm. Holes may only be made on the joist's centreline within the permitted area to a maximum diameter of 65mm. Additional holes must be at least three diameters (centre to centre) apart.
How big of a hole can you put in a 2x6?
2" x 6" = maximum 2-3/16" notch. BORED HOLES Maximum size hole = 60% of stud width: 2" x 4" = max. 2- 1/8" diameter hole.
How big of a hole can you put in a TJI?
Number of holes per span for TJI® Products Software determines the hole size relative to the depth of the joist and this size is shown in the member report. No limit for circular holes less than or equal to 1.5" in diameter and rectangular and slotted holes with both width and height less than or equal to 1".
How big of a hole can you cut in AI joist?
According to WIJMA, Holes not exceeding 1/3 of the depth of the web in any dimension are acceptable in most I-joists, and they may be round, square, or rectangular. Holes must be placed in the center third of the vertical depth of the web.
Where do you drill TJI joists?
One notch may be cut anywhere except the middle of the length of the stud or column. Holes may be drilled anywhere along the length of the stud or column but must be at least 5" from the edge.
US East
To download our VERSA-LAM ® span and size chart PDFs, click on the links below.
US West
To download our VERSA-LAM ® span and size chart PDFs, click on the links below.
BC Calc
BC Calc ® performs engineering analysis to help our customers size beams, joists, columns, studs and tall walls for their building projects. It is simple to use, yet flexible enough to analyze a variety of common applications. The user enters the member geometry, adds loads, holes and other relevant data and then selects a product for analysis.
Available RFPI Joist Sizes and Series
Not all grades and/or sizes available in all markets. Contact your Roseburg EWP representative for availability.
Additional Product Information
Roseburg RFPI-Joists are available throughout North America at some of the largest and most respected wholesale distributors and pro-yards.
Project Inspiration
Roseburg products have been specified in thousands of commercial, residential, government and education projects. View our portfolio to get inspired.