Can I use a 5/16 hose for fuel line?
First of all, this should NEVER be used as fuel line, as its not reinforced with ANYTHING, nor is it heat resistant. Second, the hose is 5/16 OD, not ID. Not even remotely the correct size to fit over a 5/16 hose barb even with heating. 3 inches too short!
Can nylon be used for fuel lines?
Today's pump gasoline / gasohol is very corrosive. If the material you are using for your fuel lines does not specifically state that it is built to withstand modern fuels, DO NOT USE IT! I wasn't sure if Nylon is compatible with modern fuels, but it is. Nylon and Teflon (PTFE) can be used for soft lines.
How big is a 1/4 fuel line?
Using calipers, I've measured the fuel line at .250" ID, .312" OD (which would "normally" be called 1/4" line). The barb fittings measure .350" at the widest barb.
What is the best material for a fuel line?
Nylon and Teflon (PTFE) can be used for soft lines. The Gates Barricade hose is built to withstand modern fuels. They make two types, one for carburated vehicles and one for EFI. And it's really not that expensive when you consider braided fuel lines run much higher than it.
What other items do customers buy after viewing this item?
Dorman 800-080 Fuel Line Quick Connector That Adapts 5/16 In. Steel To 5/16 In. Nylon Tubing, 2 Pack
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Dorman OE Solutions Fuel Line Repair Kit
When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.
Dorman OE Solutions Fuel Line
When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.
Dorman OE Solutions Fuel Line Unions
When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.
Dorman OE Solutions Fuel Line
When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.
Dorman OE Solutions Fuel Line Unions
When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.
Dorman OE Solutions Fuel Line Repair Kit
When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.
Dorman OE Solutions Fuel Connector
When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.
Why can't I use a rubber fuel line?
As near as I can tell from what I've read, molecules of gas vapor permeating and escaping rubber fuel line seems to be the #1 reason not to use it, as well as, being susceptible to road debris and accident damage.
What is the best way to replace a metal fuel line?
Option 3: Nylon. One option for replacing metal fuel lines is with a nylon tubing and specific fittings. Nylon tubing can be used for an entire length of fuel line or just a section. This option can be a cost-effective and time-efficient repair when pre-bent lines are not available.
How many options are there when replacing fuel lines?
There are three options when it comes to replacing fuel lines, and each has its advantages and disadvantages.
Can you replace hard line with flexible hose?
Do not replace long runs of hard line with flexible fuel hose. Even the best fuel injection, low-permeation fuel line will have some amount of fuel vapor loss. Also, road debris can damage the line. This is very dangerous, and it also can be difficult to seal the connection between the metal line and the hose that could be under 50 psi or more of pressure.
Can you make quick disconnect fittings?
This is an option if you are willing to invest in bending and flaring tools. If you plan to use this approach, buy a tool that can make quick disconnect fittings. These kits can be pricy, but they can pay off by increasing productivity by not having to wait for parts. But you will have to carry a basic assortment of fittings.
Can you use one long piece from the tank to the filter?
Just use what the manufacturer used don't try to re invent the wheel : no:, you can use one long piece from the tank to the filter :yup:.
Can you replace a metal fuel line?
One option for replacing metal fuel lines is with a nylon tubing and specific fittings. Nylon tubing can be used for an entire length of fuel line or just a section. This option can be a cost-effective and time-efficient repair when pre-bent lines are not available.