What are the best boat fuel lines and hoses?
High-quality fuel assembly components must be securely attached to prevent potentially dangerous boat fuel lines leaks. Find the top names in boat fuel lines and hoses including Attwood , Tempo Marine , Moeller Marine , Sierra Marine Products , MPI , Bennett Marine, and Whitecap Industries.
What kind of fuel do you put in a 5 8 Hose?
Marine Products Fuel Vent Hose 5/8" - Sold by the Foot Fuel Vent Lines - Gasoline up to 85% ethanol blended fuel, diesel fuel Meets USCG Type A2 Requirements For Pleasure Boats Resists gasoline/alcohol blended fuel Fire resistant Weather/UV... Moeller Marine 3/8" Low Perm Fuel Hose Moeller Marine fuel hoses are OEM compatible.
How much hose do I need for a fuel line?
Don't take any chances with your investment Use only marine grade hose. Fuel line hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose. Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.
What is a type a fuel hose?
EPA & CARB - Compliant, SAE J1527, USCG Type A1-15, ISO 7840-A1 Type A fuel hose is a thick walled hose usually used below deck. This hose is used for the connection between the fuel tank and the fuel water separating fuel filter. Also for connection to engine or generator.
Is marine fuel line different than automotive fuel line?
As I understand, one big difference is better UV resistance in the marine fuel line. Automotive fuel line gets a virtually no exposure to direct daylight, so little to no need for UV protection. Another possible difference is better flame resistance in the marine fuel line.
What is marine grade fuel hose?
These are specifically designed and branded for use in supplying fuel to motors in boats or marine vessels. USCG Type A1 hoses are designed for fuel feed applications where the fuel is constantly in the hose, whereas Type A2 hoses are designed for fuel fill type hoses only.
Is marine fuel hose different?
Marine-grade fuel hose is much heavier than the same inside-diameter hose as used in automotive applications. This is done as part of its fire or flame testing, a requirement under the regulations. All fuel hose used in engine room spaces on board gasoline-fueled boats must meet a 2.5-minute fire test rating.
How much horsepower will a 3/8 fuel line support?
A 3/8”id fuel line can easily support 600 HP given sufficient “pump head”! Given a big enough pump a 3/8” steel line could support 1000 HP. The simple way to know is to install an electronic fuel pressure gauge. If the pressure falls as the engine RPM's go up you need more pump head.
What is USCG approved fuel line?
MPI Fuel Hose USCG Type A This premium quality fire-retardant fuel hose meets or exceeds all requirements of new ISO 7840 and SAE J5127 standards required by USCG, ABYC and NMMA. Inner tube material provides extraordinary resistance to gasoline, diesel and alcohol-enhanced fuels.
What is the difference between A1 and A2 fuel hose?
Hose used for diesel supply and return applications must carry an A1 rating, while fill and vent installations call for hose designated as A2 (A1 is acceptable for fill and vent hose, however, A2 hose should not be used for anything other than fill or vent applications as it's not designed to be continuously filled ...
What is the best material for fuel lines?
The best fuel line material depends on your needs. However, the best material for fuel lines is polytetrafluoroethylene or PTFE. PTFE fuel line is made of plastic material specifically known as Teflon. This fuel line material is impervious is resistant to the degenerative fuel effects which could form vapor barriers.
What size is outboard fuel line?
Still allowing the proper amount of fuel to get to the engine without having any problems. Of course, the 3/8″ fuel line will work for any of the outboards. But most smaller outboards have fittings or quick connects on them that are set for a 5/16″ hose. It's basically the standard hose for the smaller engines.
Can I use rubber hose to repair fuel lines?
Standard rubber vacuum or heater hose should never be used in fuel applications. The hose will deteriorate from the inside out and can plug fuel filters and carburetors with rubber debris, long before it springs an external leak.
What size fuel line should I run?
Recommended Size, Based on HorsepowerRecommended Fuel Line Size (from the tank to the pump)Engine OutputSize (inches)Size (AN)350 hp or less5/16 in.-5350-450 hp3/8 in.-6450-650 hp1/2 in.-81 more row•Sep 16, 2017
Does fuel line size affect pressure?
Shows the relationship between measured pressure drop as a function of flow rate, for four different fuel lines (two different sizes at two different lengths). Every fuel line experiences pressure loss depending on fuel line length, and fuel flow rate.
What size fuel return line should I use?
The Fuel Return Line should be at least the same size, or one size larger than the supply. Make sure there are no sharp bends or kinks. The return line should direct fuel close to the bottom of the tank and away from the pickup.
Compare with similar items
There was a problem filtering reviews right now. Please try again later.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Details
Type A fuel hose is a thick walled hose usually used below deck. This hose is used for the connection between the fuel tank and the fuel water separating fuel filter. Also for connection to engine or generator. Provides extraordinary resistance to gasoline, ethanol, diesel and alcohol-enhanced fuels!
Reviews
Only registered users can write reviews. Please Sign in or create an account
Special offers and product promotions
Amazon Business: Make the most of your Amazon Business account with exclusive tools and savings. Login now
Have a question?
There was a problem completing your request. Please try your search again later.
Product description
Excellent resistance to fire, heat, ozone, and permeation by alcohol blended gasoline and diesel fuels. Compounded to meet or exceed SAE-J1527 Type A, ISO/DIS 7840, and NMMA. Made in the USA. Product may differ from picture.
Featured items you may like
Pages with related products. See and discover other items: fuel hoses, fuel line for car, feed line hose
What are boat fuel lines?
Boat fuel lines and hoses in any boat’s fuel systems are essential in ensuring safe boat operation and trouble-free performance. High-quality fuel assembly components must be securely attached to prevent potentially dangerous boat fuel lines leaks. Find the top names in boat fuel lines and hoses including Attwood , Tempo Marine , Moeller Marine , Sierra Marine Products , MPI , Bennett Marine, and Whitecap Industries. It is vital to understand marine fuel hose-related issues to assure these components are fully functional and safe or if these components are in need of replacement.
How to check if a fuel tank connector is suction?
Check for suction at the tank end by covering the hose end with your finger.
What is the Moeller 033802-10?
Moeller Marine 033802-10 Aluminum Anti-Siphon Barb Anti-siphon valves, are required by Federal Law and the USCG on all permanent fuel tank installations. Use 15 (Brass) calibrated for HP 200 & above and 30 (Aluminum) calibrated for HP below 200...