What is the ID of a 3/8 hose?
How to Interpret Hose, Tube & Fittings "Dash Sizes"HOSE I.D (Inches)All EXCEPT Transportation & Refrigerant Hoses-63/810-81/212,5-105/81611 more rows
Is rubber hose measured by ID or OD?
Inside Diameter, or I.D., is the primary measurement used in identifying a hose's size. A ¾ inch hydraulic hose means the inside diameter of that is ¾ of an inch. Fittings that are used for a hose assembly will be identified by the same inside diameter measurement, i.e. a ¾ inch fitting for a ¾ inch hose I.D.
What size ID is hose?
In the vast majority of common hydraulic hoses, the I.D. measurement is divided into 1/16” increments known as the “dash size.” For example, a hose measuring 3/4” ID will be shown as a “-12” coming from the numerator of the fraction of 3/4″=12/16”. A 1” ID would be 16/16 or a -16, and so on.
What is the OD of 3/8 rubber hose?
uxcell Silicone Tubing, 3/8"(10mm) ID X 5/8"(16mm) OD 3.3ft Silicone Rubber Tube Air Hose Water Pipe for Pump Transfer Black.
What is ID tubing?
Tubing is measured using the size of the inside diameter (I.D.) and outside diameter (O.D.). The measurement between the inside and outside diameter of a plastic tube is referred to as “the wall” and is used to measure tube strength: the thicker the wall, the stronger the tube.
How do you find the diameter of rubber?
0:453:13How To Measure the Diameter Of Any Hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo of course the first step is just grabbing your tape measure every tape measure may be a littleMoreSo of course the first step is just grabbing your tape measure every tape measure may be a little bit different for example if I count the number of spaces.
What size is 3/8 hose?
For example: a 3/8" standard hose equals -6 AN....Russell Performance Technical Support.AN SizeMetal Tube O.D.Thread Size-3 AN3/16"3/8" - 24 SAE-4 AN1/4"7/16" - 20 SAE-5 AN5/16"1/2" - 20 SAE-6 AN3/8"9/16" - 18 SAE5 more rows
What size is after 3/8 hose?
HOSE SIZESDash SizeInside Diameter-55/167.9-63/89.5-81/212.7-105/815.98 more rows
What size is #20 hose?
The standard worm drive hose clamps come with a 5/16" slotted hex head screw....Full-Size Worm Drive Hose Clamps.Full-Size Worm Drive Hose Clamp Size Chart121/2" - 1-1/4"13 mm - 32 mm1613/16" - 1-1/2"21 mm - 38 mm2013/16" - 1-3/4"21 mm - 44 mm241" - 2"25 mm - 51 mm21 more rows
What is rubber tubing?
“Rubber tubing” is a term that refers to hollow synthetic and natural rubber channels, or flow lines, that transfer or dispense liquids and gases. With their varying chemical compositions, rubber tubings' characteristics are quite diverse, which is advantageous for professionals who wish to engage tubing.
What is EPDM hose?
A preferred choice for air and water service, oil mist lubricating air lines and agricultural chemicals, the 3/8" EPDM Service Hose is a versatile general-purpose rubber hose. Reinforced with 2-spiral high tensile textile cord, this tubing has excellent coupling retention and kink resistance. The EPDM tube and cover resists heat, sunlight, ozone and weathering. This tubing stays flexible in temperatures as low as -40° F. and has a 200 maximum PSI. Exceeds RMA class C medium oil resistance requirements. Not suitable for the transfer of petroleum products or anhydrous ammonia.
Is a sprayer tubing flexible?
Yes, this tu bing is fairly flexible and would be a good choice on a sprayer.
Can you use a propane hose with petroleum products?
Unfortunately, we do not carry a hose that can handle petroleum products and are not rated for use with propane.
Does a brake hose handle petroleum based fluid?
No this hose will not handle brake fluid which is either glycol-ether based or petroleum based. Both of which will damage the hose.
What size hose to use for RV1?
RV1 OVER THE PIPE HOSE RV1 hose can slip over piping outer diameters for a sleeve fit. 7/8" to 4-1/2" inner diameters. -0F to 212F.
What size hose is used for a concrete pump?
With standard VIC or HD fittings, as well as metric and clamps. 1-1/2" - 5" diameters.
What is a RP3-AS?
RP3-AS HARDWALL GASOLINE CURB PUMP HOSE RP3-AS assemblies are used for petroleum and gas dispensing from pumps, and include a hardwall construction. Also widely used for other fuel applications. It has a long service life and kink resistance. Comes in standard lengths with fittings. UL 330 approved. 5/8" & 1" diameters. -40F to 120F.
What is a RM1 hose?
RM1 MULTIPURPOSE RUBBER NITRILE HOSE RM1 is a premium quality multipurpose Nitrile hose that is recommended for many abusive industrial applications up to 2" diameters. It is oil resistant and right for air, water, and many chemicals as well, and has excellent kink and abrasion resistance. -20F to 180F.
What is a RSW winery hose?
RSW WINERY HOSE The Model RSW Winery Hose is a heavy duty hose formulated for the suction and transfer of wine, fruit juice, and soft drinks. It has a white, smooth bore EPDM rubber tube to ensure no effect on odor or taste. allows for the sterilization of the hose with steam. 3/4" to 4" diameters. -40F to 248F.
What is RS3 food hose?
RS3 EPDM FOOD HOSE RS3 Food Hose is a multipurpose sanitary hose suitable for suction and transfer of foodstuffs and potable water with no added odor or taste. EPDM tube with UHMWPE outer cover for high abrasion resistance, dragability, and is Antimicrobial. 1" to 4" diameters. -40F to 284F.
What is a RT1 steam hose?
RT1 STEAM HOSE RT1 is a quality rubber steam hose with a heat resistant EPDM tube and cover for maximum life. 1/2" to 2" diameters. -20F to 415F.