Here’s the throttle body relearn procedure 1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal.
Full Answer
How to reset and relearn the TPMs on a Chevy car?
Instruction on How to reset and relearn the TPMS on Chevy Cars. A relearn magnet, or another properly formatted TPMS scan tool, is required to perform this procedure. Relearn Procedure. 1. Inflate all tires to pressure listed on the placard. 2. Make sure the vehicle has been in park for at least 2 minutes before proceeding. 3.
What is the idle relearn procedure on a Chevy Chevy Silverado?
Chevy uses a simple idle relearn process. After you replace the computer chip, it will automatically reset itself when you turn the ignition key from the "on" position to the "off" position. Blue Streak Electronics recommends to warm the engine after the idle relearn procedure, without use of the air conditioner.
What is the throttle body relearn procedure?
Here’s the throttle body relearn procedure 1 Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2 After 3 minutes, turn the engine off and leave it off for 60- seconds. 3 Start the engine again and let it idle in park for 3 minutes one more time. ... More items...
What is the correct TPMS scan order?
Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor.
How do you reset the throttle body on a 2013 Silverado?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutesMoreNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutes again after the 3 minute runtime the engine should be idling normally.
How do you reset the throttle position sensor on a Chevy?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do you relearn the throttle position sensor?
1:112:42When Should I Reprogram My Car's Throttle Body? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.28-Dec-2016
How do you calibrate a TPS sensor?
1:0010:54How to install & calibrate a new Throttle Position Sensor (TPS) #1208YouTubeStart of suggested clipEnd of suggested clipNow you'll usually find the TPS unit they have a slot on the top. So that you can undo the pinchMoreNow you'll usually find the TPS unit they have a slot on the top. So that you can undo the pinch bolt. And we can very accurately rotate this on the casting. To get the output voltage.
How do I reset my electronic throttle control system?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.
How do you reset throttle body after replacing?
How Do You Reset Throttle Body After Replacing? In a moment, hold the key to the “On” position again, wait another 3 seconds, and repeatedly press the accelerator. Hold the accelerator steady for 7 seconds.12-Feb-2022
What happens if you unplug TPS?
The TPS as we call it is one of the most important sensors on the engine. Without it, the computer has no way of knowing when you push down on the gas or open the throttle. Best it can do it watch some other sensors and make some estimated guesses. On some cars, it may burp just as you unplug it if it's running.
How do I reset my throttle body after cleaning?
The idle will relearn if you put the vehicle in drive and allow the idle to come down with all accessories off for about two to three minutes. Then turn on your a/c with blower in high position for three minutes. This should fix it.18-Jan-2016