Here’s the throttle body relearn procedure 1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds.
Full Answer
How do I perform a throttle Relearn on a GM throttle-by-wire vehicle?
Performing a throttle relearn on GM throttle-by-wire vehicles can easily be done with the Mac Tools Mentor Touch Scout, No. ET6100. For example, to perform a throttle relearn on a 2008 Silverado 5.3L, select and run the Idle Learn Reset test. Then start the engine and allow the ECM time to begin to learn.
What does the throttle position sensor do on a Chevy Silverado?
Your Silverado's throttle body is an air-intake butterfly valve that regulates air flow. Removing it and replacing it with a shiny, new throttle position sensor (TPS), or a new unit all together can keep your truck running strong.
How do I Reset my electronic throttle body?
Also to know is, how do I reset my electronic throttle body? Turn the ignition switch on and wait 3 seconds. Immediately after the 3 seconds, the accelerator pedal must be pressed and released 5 times within 5 seconds.
What should I do if my throttle body has carbon?
If carbon is present, follow the Throttle Body Cleaning Procedure in SI to clean the throttle body. After ensuring that the throttle body bore and plate are clean, perform an "idle learn reset/ idle learn" with the Tech 2 and re-evaluate the concern.
How do you reset the throttle body on a 2009 Chevy Silverado?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutesMoreNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutes again after the 3 minute runtime the engine should be idling normally.
How do I relearn my electronic throttle body?
1:112:42Throttle Body Relearn: When Should I Reprogram My Car's ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
How do I reset my GM electronic throttle control manually?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.
How do you reset the throttle position sensor on a Chevy Silverado?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
What happens if you don't relearn your throttle body?
What happens when you replace the throttle body? If you replace the throttle body, the PCM won't know and will continue to use the adaptive settings as if the carbon buildup is still in place. If you don't do a relearn procedure, the PCM will “hunt” for a new baseline idle.
How do you relearn a Chevy idle?
After the engine is warm, switch the air conditioning on and off, and then put the transmission into the "drive" position. These actions complete the full idle relearn procedure.
How do you calibrate a throttle position sensor on a Chevy?
3:224:22How to Calibrate Throttle Position Sensor Using a Multimeter (Set TPS)YouTubeStart of suggested clipEnd of suggested clip45 volts and then as you apply throttle. You should see the voltage. Increase steadily up to aboutMore45 volts and then as you apply throttle. You should see the voltage. Increase steadily up to about four and a half volts uh or all the way up to five we should be good to go here.
How do you reset throttle body after replacing?
Leave the key off for a moment, turn the key to the "On" position again, wait 3 seconds, and press the accelerator 5 times in 5 seconds. Wait 7 seconds, and hold the accelerator down. The check engine light should start blinking, continue to hold pedal down until it stops blinking. You can then start the car.
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.
How do you reprogram a throttle position sensor?
How to Reset Throttle Position SensorPut the key in the ignition.Turn the key to the On position, without cranking the engine. Wait a few seconds, then turn it off.Repeat the second step.Crank the engine.Pull the parking brake.Set the gear lever in Drive.Wait 5-10 minutes.
How do you adjust the idle on a GM throttle body?
3:015:54How to: GM TBI Idle Adjustment - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you'll just I took a drill bit drilled it out and it should be a t25 to adjust it we will turn itMoreSo you'll just I took a drill bit drilled it out and it should be a t25 to adjust it we will turn it clockwise. I think to advance the idle.
How do I calibrate my accelerator pedal position sensor?
To calibrate the accelerator pedal assembly: To recalibrate the ECM and accelerator pedal, the ignition switch must be in the ON position and then the accelerator pedal must be slowly and fully depressed from idle to full throttle. Repeat the procedure three times.
Step 1 – Open hood and pop off plastic engine cover
That behemoth of a top cover on your Vortec V8 is held on by only two tabs. Gently lift the front until it pops up from its post, then reach under and toward the rear of the cover to pop the back tab. (It's so easy, a US Congressman could do it!)
Step 3 – Remove air intake tubing
At each end of the intake tubing, you'll see a worm-drive clamp. Loosen both clamps at the air cleaner and TB unit. There will also be a tab at the far left side rear. Simply pop that off. Finally, unplug the sensor plug on the intake tube.
Step 4 – Remove power leads to the throttle body
Simply push down on the gray clip tab, and remove the entire plug. You should not have to remove the pink clip.
Step 5 – Remove the throttle body assembly
Using a 10mm wrench, remove the two nuts and two bolts. Then, slide the TB off the studs.
Step 6 – Inspect O-ring and replace if needed
The O-ring should be intact; however, if it has any cuts, abrasions, or is just plain grungy, you should have a new gasket in the new throttle body kit.
Step 7 – Install the new (or refurbished) throttle body
Simply line up the stud screws and slide the unit in place. Tighten the nuts and lower bolts in a crisscross pattern until tight. Do not over tighten! There is no torque spec for these, so use common sense when tightening. Plug the sensor plug in, and secure it with the gray clip.
Step 8 – Reinstall air intake assembly and cover
Install the plastic air intake tubing assembly, tighten the worm-drive clamps, and push the PCV valve back in place. Simply line up the front and rear tabs on the engine cover. Then, push down firmly until it snaps into place. Plug in the sensor at the air cleaner end of the intake.
What to do after cleaning a GM throttle body?
After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn. After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn.
Can you throttle relearn without a scan tool?
Throttle relearn can also be done without a scan tool, essentially by letting the vehicle idle in park for several minutes and allowing time for the ECM to learn. See appropriate service information for vehicle specific procedures and details if you wish to perform a throttle relearn in this way. Information provided by Mac Tools.