2009 Chevrolet Malibu Ignition Transponder Chip Key Programming Instructions
- Insert a new cut key in ignition and turn key to the ON position for 10 minutes and 30 seconds.
- Within 45 seconds turn the key to OFF and then back to the ON position for 10 minutes and 30 seconds.
- Within 45 seconds turn the key to OFF and then back to the ON position for 10 minutes and 30 seconds.
- Turn key OFF then back ON. The key is now programmed. ...
- Enter your Malibu and close all the doors.
- Insert your key into the ignition. ...
- Press and hold the "Unlock" tab on the driver's side door as you insert and remove the key from the ignition three times.
- Release the "Unlock" tab. ...
- Repeat Step 4 for any additional remotes.
How do you program Chevy Malibu key fob?
- Enter your vehicle. Work will be done on the driver's side.
- Locate the OBD2 Port.
- Close the door you entered through.
- Insert car key into the ignition.
- Insert the key fob into the port.
- Wait for a chime or red light.
- Press and hold the lock and unlock button on the remote at the same time.
- Remove the key fob.
How to program a key for a Chevy Malibu?
Programming a new Chevy key, assuming you already have a blank key, basically involves two phases: 1. Cutting the key or remote so it will fit your car’s ignition. Before the key can be programmed, it needs to be cut to fit your car.
How to program a Chevrolet key fob?
How to program a key fob. 1. Replace the batteries inside the key fobs. 2. Get inside the car. 3. Turn on the ignition. 4. Press the lock button on the remote key.
How to program Chevrolet Malibu remotes?
- Sit in the driver's seat.
- Remove the ignition key from the ignition lock cylinder.
- Close all the doors.
- Press and hold unlock on the door lock switch (on the door)
- While holding the door lock switch in the unlock position, insert and remove the ignition key twice.
How do you program a 2009 key fob?
0:222:061999-2009 Toyota Keyless Entry Remote Fob Programming Video ...YouTubeStart of suggested clipEnd of suggested clipTurn the ignition to on but do not start the car then turn back to off once to program remote whileMoreTurn the ignition to on but do not start the car then turn back to off once to program remote while retaining the original remote coats twice to erase all original codes and add a new remote.
Can you program a key fob by yourself?
Can you program a new key fob yourself? If it is only the key fob itself to unlock the car, you can most often program it yourself. However, programming a key for the start function is impossible without the right tools.12-Feb-2022
How do you program a key fob for a Chevy Malibu?
On the Chevy key fob, press and hold the “Unlock” and “Lock” buttons at the same time until you hear the door lock and unlock again. This means you're all set. Re-insert the programmed key back into the ignition to the “On” position to finish the Chevy key fob programming process.
How do you reprogram a Chevy key fob?
On your Chevy key fob, press and hold the “Unlock” and “Lock” buttons simultaneously until you hear the door locks engage and disengage again, indicating that you have successfully programmed your key fob. Re-insert the newly programmed key into the ignition in the “On” position to end the programming sequence.
Anonymous
Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
mike ryner
Your key can only be programed at the dealer. They have to use a scan tool and a unique id code that they get from the factory. It is done this way to help insure that the vehicle is less likely to be stolden.
blueextc3221
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote.
Richard Scordino
Your numbers aren't that far off...the mpg posted is established using professional drivers...I could likely coax a few more mpg out of your car if I drove it because I know how.
mike
you mean the oil life richard if so hold the info and enter button on steering wheel at same time oil life will come up then release hit enter again and it resets,good luck, mike
Remote key
Yes - Sometimes when the battery is replaced the key program can be corrupted. It would be a starting point to have the key reprogrammed just to eliminate it as a source of trouble.
How to program keyless entry remote for 2009 chevy malibu
Unfortunately your 2009 Chevy Malibu key fob does not have any self programming procedures. You have to have a professional program this key fob to your vehicle. I do have a couple money saving tips for you:
My 2009 Chevy Malibu will no longer start remotely from the key fob. The alarm will sound and the lights will flash when I attempt to start it from the remote. How do I fix this?
Possible low/partially shorted vehicle battery. I would have the battery/charging system thoroughly tested. Depending on when your 2009 Malibu was manufactured, (possibly in mid-2008) your battery is getting to be close to 4 years old. It may be time to replace it.
2005 chevrolet malibu
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote.