What are the signs of a bad throttle position sensor?
Top 6 Bad Throttle Position Sensor Symptoms
- Car Jerks. Jerking or bucking of the vehicle is the most common symptom of a bad TPS. ...
- Idle Surging. Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is ...
- Check Engine Light. ...
- Engine Stalling. ...
- Acceleration Issues. ...
- Problems Switching Gears. ...
What does a bad throttle position sensor do?
When the throttle position sensor goes bad, one of two things happens: The fuel injection computer no longer receives any throttle plate angle information. The fuel injection computer receives incorrect throttle angle position information. Both scenarios are not good, since they'll cause engine performance problems.
How to replace a throttle position sensor?
How to Replace a Throttle Position Sensor. Remove the battery Before you begin, detach the negative terminal connection from the battery. This will prevent you from receiving undesired shocks as well as causing harm to other components under the hood. Unplug the Previous Sensor
Will a throttle position sensor keep a car from starting?
Hereof, can a throttle position sensor stop a car from starting? The only way a TPS will cause a no-start is if the TPS is busted/stuck, and the TPS is telling the computer that you've floored the gas.
How do you change a throttle position sensor on a Chevy Silverado?
2:503:55Replace Throttle Position Sensor Tahoe, Silverado, and SuburbanYouTubeStart of suggested clipEnd of suggested clipYou're gonna push in on the throttle body. And this is what huh. So you're gonna push. Inside on theMoreYou're gonna push in on the throttle body. And this is what huh. So you're gonna push. Inside on the intake to line up that bottom bolt with your new sensor. Take your new clips.
What are the symptoms of a failing throttle position sensor?
Symptoms of a Bad or Failing Throttle Position SensorCar won't accelerate, lacks power when accelerating, or accelerates itself.Engine won't idle smoothly, idles too slowly, or stalls.Car accelerates, but won't exceed a relatively low speed, or shift up.More items...•
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.
How do you reset the throttle body sensor on a Chevy Silverado?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutesMoreNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutes again after the 3 minute runtime the engine should be idling normally.
Will TPS cause transmission problems?
Throttle Position Sensor It is used to determine engine load and if it fails it can cause automatic transmission shifting problems.
What is the code for throttle position sensor?
The most common throttle position sensor code is the P0122 – Throttle Position Sensor/Switch A Circuit Low Input. It's triggered when the ECU detects that the TPS circuit A is outputting a lower voltage than expected.
Does a throttle position sensor need to be programmed?
Code errors can cause your throttle position sensor to work erratically or incorrectly. Otherwise, you'll need professional software to reprogram your sensor. This job is best done by a professional mechanic.
How do you reprogram a throttle position sensor?
1:112:42Throttle Body Relearn: When Should I Reprogram My Car's ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
What happens if you don't relearn your throttle body?
What happens when you replace the throttle body? If you replace the throttle body, the PCM won't know and will continue to use the adaptive settings as if the carbon buildup is still in place. If you don't do a relearn procedure, the PCM will “hunt” for a new baseline idle.
How do you calibrate a throttle position sensor on a Chevy?
3:224:22How to Calibrate Throttle Position Sensor Using a Multimeter (Set TPS)YouTubeStart of suggested clipEnd of suggested clip45 volts and then as you apply throttle. You should see the voltage. Increase steadily up to aboutMore45 volts and then as you apply throttle. You should see the voltage. Increase steadily up to about four and a half volts uh or all the way up to five we should be good to go here.
How do you adjust the throttle position sensor on a Chevy?
0:573:46TPS or Throttle Position Sensor Adjustment 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idleMoreBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idle speed. And then readjusting the TPS. The desired idle condition can always be met by the engine.
How much does it cost to fix a throttle position sensor?
The average replacement cost for the throttle position sensor is anywhere from $110 to $200. The parts cost is anywhere from $75 to $105 while the labor cost is anywhere from $35 to $95.
1 Answer
An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
Bill Boyd
An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
Where should the throttle sensor be mounted?
It should be mounted to your throttle body, which is on top of your engine. You should disconnect your negative battery cable before removing the sensor. This helps you avoid the risk of electrical shock or causing an error code on your engine control module.
What is the function of the throttle position sensor?
When you press down on the gas pedal, your throttle body unit's valve opens. This causes your throttle position sensor to adjust the engine intake manifold accordingly .
Why is my throttle position sensor not working?
Code errors can cause your throttle position sensor to work erratically or incorrectly. Otherwise, you’ll need professional software to reprogram your sensor. This job is best done by a professional mechanic. If your sensor just needs repairs, it could be the result of faulty or loose wiring.
How to install a new sensor?
Install your new sensor by working backward through the removal steps. Start by installing the sensor using the mounting screws. Next, connect your sensor to your vehicle's electrical system using a convenient electrical connector. You should be able to easily push it together and hear a distinct click. Check to ensure a firm connection.
Why does my engine keep idling?
Similarly, if your engine struggles to idle efficiently, it could also be a result of a damaged throttle position sensor. Stalling, surging, or hesitating while idling all can be caused by this unassuming sensor.
Can you replace a sensor?
Completely replacing your sensor may be the best way to avoid future issues, but some issues can be easily fixed by reprogramming or repairing your sensor. Reprogramming or resetting your sensor can sometimes solve these issues. This step can also be necessary when you install a new sensor.
Is throttle position sensor a corrosion sensor?
Just like any other electrical wiring, your throttle position sensor is susceptible to corrosion and faulty connections. Once you’ve established the issue is with your sensor and that it isn’t a programming fault, check the wiring and connection points before purchasing a new one.
Why does my Silverado have a rough idle?
Without a proper air and fuel mixture, your Silverado won't reach its optimal engine performance and fuel economy. In effect, you should notice a rough idle, stalling, engine knock or misfires, and a hesitation on acceleration, all of which can be caused by a faulty TPS. To make sure that it's your truck's TPS causing these problems, ...
How to remove air intake hose?
Step 1 – Remove the air intake hose. Open the hood and use a flat head screwdriver to loosen the hose clamp on each end of the air intake hose. One hose clamp is located by the MAF sensor, and the other is located by the throttle body. Once the hose clamps are loose, slide the air intake hose out and set it aside. Figure 1.