Performing a throttle relearn on GM throttle-by-wire vehicles can be done with your scan tool. To perform a throttle relearn on a 2008 Silverado 5.3L for example, select and run the Idle Learn Reset test. Then start the engine and allow the ECM time to begin to learn.
How to perform a throttle relearn test on a 2008 Chevy Silverado?
2008 Silverado Throttle Body Relearn - XpCourse. Best www.xpcourse.com. Here's the throttle body relearn procedure 1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds. 3) Start the engine again and let it idle ...
How to program a throttle position sensor?
Performing a throttle relearn on GM throttle-by-wire vehicles can be done with your scan tool. To perform a throttle relearn on a 2008 Silverado 5.3L for example, select and run the Idle Learn Reset test. Then start the engine and allow the ECM time to begin to learn. Clear any DTCs. In some cases it may be necessary to drive the vehicle before ...
What is the throttle body relearn procedure?
21/06/2015 · Here’s the throttle body relearn procedure. 1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds. 3) Start the engine again and let it idle in park for 3 minutes one more time.
Do you need to perform a throttle/idle Relearn on a GM vehicle?
Performing a throttle relearn on GM throttle-by-wire vehicles can easily be done with the Mac Tools Mentor Touch Scout, No. ET6100. For example, to perform a throttle relearn on a 2008 Silverado 5.3L, select and run the Idle Learn Reset test. Then start the engine and allow the ECM time to begin to learn.
How do you reset the throttle position sensor on a Chevy Silverado?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do you relearn the throttle position sensor?
1:112:42When Should I Reprogram My Car's Throttle Body? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
How do I reset my GM electronic throttle control manually?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.28-Dec-2016
How do I reset my Chevy throttle body?
Fully depress the accelerator pedal for 10 seconds. At this point the check engine light should change to blinking slowly indicating “Erasing ECU Memory”. 8. Release the accelerator pedal and turn the ignition switch to off.
How do you calibrate a throttle position sensor?
1:544:19How to replace / calibrate your throttle position sensor TPS (Honda)YouTubeStart of suggested clipEnd of suggested clipYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to theMoreYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to the negative lead of the battery. And the positive lead should be connected to the little red wire.
How do you reset the throttle body on a 2008 Chevy Tahoe?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutesMoreNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutes again after the 3 minute runtime the engine should be idling normally.
How do you reset the ECM on a Chevy truck?
There's no complicated reset procedure; You just need to cut off power for a long enough time where the ECM forces a reset when it regains power once more.
How do you calibrate a throttle body?
0:093:26Throttle Calibration- Relearn? Car Feels Different - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut your car in the run. Position. Once everything is good press down on the gas. And hold it downMorePut your car in the run. Position. Once everything is good press down on the gas. And hold it down for 20 seconds slowly let off the gas. Okay then put the car in the off.
How do you adjust the throttle position sensor on a Chevy?
0:573:47TPS or Throttle Position Sensor Adjustment 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idleMoreBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idle speed. And then readjusting the TPS. The desired idle condition can always be met by the engine.
How do I reset my throttle body after cleaning?
The idle will relearn if you put the vehicle in drive and allow the idle to come down with all accessories off for about two to three minutes. Then turn on your a/c with blower in high position for three minutes. This should fix it.18-Jan-2016
What happens when you unplug throttle position sensor?
The TPS as we call it is one of the most important sensors on the engine. Without it, the computer has no way of knowing when you push down on the gas or open the throttle. Best it can do it watch some other sensors and make some estimated guesses. On some cars, it may burp just as you unplug it if it's running.
What to do after cleaning a GM throttle body?
After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn. After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn.
Can you throttle relearn without a scan tool?
Throttle relearn can also be done without a scan tool, essentially by letting the vehicle idle in park for several minutes and allowing time for the ECM to learn. See appropriate service information for vehicle specific procedures and details if you wish to perform a throttle relearn in this way. Information provided by Mac Tools.
How to reset a dtc?
Remove negative battery cable for 20 minutes to reset all DTCs. 2. Start engine, run in park for 3 minutes. -MIL did not come on. -Engine starts at about 1200rpm, then slowly idles down to 800 rpm and back up to a steady 1000rpm. 3. Remove key for 60 seconds. 4. Start engine, run in park for 3 minutes.
Is idle normal while driving?
While driving, the idle was pretty normal , although downshifts came with a noticable surge, especially the 2-1 when coming to a complete stop. Behavior continued to improve over the next several days, and after about 500 miles of driving has returned to what I would consider normal.
How to program a throttle in a car?
First step calibrating or programing your car throttle is to sit in your car and form the accelerator pedal released position learning. Do not depress the accelerator pedal when you turn the keys on wait for at least 2 seconds for each action. You need to know that the timing of this is important. So when you positioned yourself ready ...
How to program throttle position sensor?
Steps on How to Program a Throttle Position Sensor for a Throttle Valve Closed Position Learning. Step 1. Start by forming the throttle valve closed potion leaning. Step 2. Be sure that the accelerator pedal is totally freed or released. Step 3. Then grab the keys and turn “ON” the ignition switch. Wait 10 seconds.
How to release the accelerator pedal?
Step 1. Make that the accelerator pedal is completely released or free, then turn “ ON” ignition switch and wait for 3 seconds. Step 2. You want completely depress the accelerator pedal very hard and fully release the accelerator pedal as quickly as possible 5 times within 5 seconds.