Remove ducting from air cleaner to throttle entrance. Spray with carb. choke cleaner or WD40 spray and wipe back to the alloy finish. clean the the throttle plate and push the throttle open with your fingers and clean in behind as best you can. Clean the passageways to the idle air control valve.
Full Answer
What kind of throttle body cleaner does a GMC Sierra use?
These are the materials most of the components on the intake manifold, plastic plenum, and the insides of the electronic throttle body are made up of on your GM vehicle. The recommended throttle cleaner is the: CRC 05078 Throttle Body and Air-Intake Cleaner - 12 Wt Oz..
Can you use carburetor cleaner to clean throttle body?
Cleaning the electronic throttle body is not hard to do. But you do need to take some very important precautions: The cleaning spray that you use must not contain Methyl Ethyl Ketone (MEK) . This means that you can not use most (if not all) brands of carburetor cleaner spray.
What kind of maintenance does a GM Electronic throttle body need?
Cleaning the throttle plate and throttle plate bore on the 4.8L, 5.3L, and 6.0L GM electronic throttle body is one of the most important routine maintenance services that should to be done on your GM pickup or SUV. Why?
What is the recommended throttle body and air intake cleaner?
The recommended throttle cleaner is the: CRC 05078 Throttle Body and Air-Intake Cleaner - 12 Wt Oz.. You should NOT use any type of scraper tool or screw driver to scrape of the deposits that have accumulated on the throttle plate or throttle bore.
Does cleaning throttle body do anything?
While throttle-body cleaning is good preventative car maintenance, it should also help engine drivability. In fact, if you've noticed a rough idle, stumbling initial acceleration or even stalling – all when the engine is fully warmed up – a dirty throttle body could be the culprit.
How do you reset the throttle body on a 2008 Chevy Silverado?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutesMoreNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutes again after the 3 minute runtime the engine should be idling normally.
How do I reset my throttle body after cleaning?
1:112:42Throttle Body Relearn: When Should I Reprogram My Car's ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
How do you know if your throttle body needs to be cleaned?
The 7 Signs That Could Mean Your Throttle Body Needs CleaningGrime Build Up. ... Poor Fuel Economy. ... Poor or High Idle. ... Uneven or Slow Acceleration. ... Electrical Problems. ... Airflow Disruptions. ... Check Engine Light.
What happens if you dont reset throttle body?
If the TPS is causing your ECM to think that the throttle is closed when it isn't, it'll reduce the amount of fuel in the air/fuel mixture and cause the engine to run lean. Without enough fuel in the mixture, the engine will fail to make as much power as it normally does.
What happens if you don't relearn your throttle body?
What happens when you replace the throttle body? If you replace the throttle body, the PCM won't know and will continue to use the adaptive settings as if the carbon buildup is still in place. If you don't do a relearn procedure, the PCM will “hunt” for a new baseline idle.
What are the symptoms of a dirty throttle body?
When the throttle body gets dirty, it has a direct effect on how smoothly the engine operates. Signs indicating a problem include rough idling, jumpy or sluggish acceleration, poor fuel economy, and stalling. With the use of a throttle body cleaning product, the dirt and debris buildup are easily removed.
Why does my truck idle high after cleaning throttle body?
Cleaning the throttle body allowed more air to enter the engine, and the computer is compensating by adding more fuel. The idle will relearn if you put the vehicle in drive and allow the idle to come down with all accessories off for about two to three minutes.
Should I reset ECU after cleaning throttle body?
Computers do not need to be reset in the event of tuberculosis testing. Now, it suggests that perhaps you moved the throttle position sensor, if you did that, your idle will light up, you will feel like the computer is shutting down, etc.
How much does it cost to get throttle body cleaned?
RepairPal.com suggests that a throttle body cleaning costs between $226 and $290. What's interesting to note is the price of parts: $6 to $12, the low estimate of which is about twice the cost of a can of CRC Throttle Body Cleaner at your average auto parts store.Nov 27, 2017Where Is My Throttle Body and Why Does It Need Cleaning? - BestRidehttps://bestride.com › news › technology › where-is-my-t...https://bestride.com › news › technology › where-is-my-t...Search for: How much does it cost to get throttle body cleaned?
Does seafoam clean the throttle body?
5:256:30Seafoam--can't believe what it did to my engine part 2--throttle body clean !!YouTubeStart of suggested clipEnd of suggested clipWell that didn't take long to clean out and throttle-body just want once again say thank you toMoreWell that didn't take long to clean out and throttle-body just want once again say thank you to Ashley for the recommendation on cleaning out the throttle body the truck definitely runs smoother.Seafoam--can't believe what it did to my engine part 2--throttle body clean!!https://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: Does seafoam clean the throttle body?
Can a dirty throttle body cause rough idle?
If your car runs rough when idling, the cause just might be a dirty throttle body. The throttle body controls the amount of air the engine takes in, and when it gets dirty, the engine can't idle smoothly.Oct 15, 2019How to Clean a Throttle Body (DIY) - The Family Handymanhttps://www.familyhandyman.com › project › cleaning-a-t...https://www.familyhandyman.com › project › cleaning-a-t...Search for: Can a dirty throttle body cause rough idle?
1 Answer
An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
john h
An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
What is the best throttle cleaner?
The recommended throttle cleaner is the: CRC 05078 Throttle Body and Air-Intake Cleaner - 12 Wt Oz.. You should NOT use any type of scraper tool or screw driver to scrape of the deposits that have accumulated on the throttle plate or throttle bore.
What happens when you put gum behind a throttle plate?
Well, when gum and other oil and carbon deposits form behind the throttle plate and accumulate to the point that they may interfere with the throttle plate movement and strip the plastic gears that make up the Throttle Actuator Motor that opens and closes the throttle plate.
Can you use carburetor cleaner spray?
This means that you can not use most (if not all) brands of carburetor cleaner spray. Methyl ethyl ketone is not corrosive for metals, but attacks certain plastics and materials including natural rubber, nitrile rubber, polyvinyl chloride, Viton®, certain acrylics and celluloses.
Can you clean an electronic throttle body?
Basics Of Cleaning The Electronic Throttle Body. Cleaning the electronic throttle body is not hard to do. But you do need to take some very important precautions: The cleaning spray that you use must not contain Methyl Ethyl Ketone (MEK) .
How many miles does a 2001 Tahoe 4x4 have?
2001 Tahoe 4x4 with the 5.3.. 97000 miles.. When the truck had around 50000 miles it started stalling and at idle the rpms would nearly bottom out and almost cut off then jump back around the normal idling range.. took to dealer and they removed entire throttle body and cleaned.. said it was really nasty..within 4 months it was back there and they removed it again for another cleaning and said it was really nasty again.. well between now and then every few months this symptom has returned and I have used the appropriate throttle cleaner and have sprayed the butterfly which gets gummed up every few months and it will idle fine and then the same thing returns... have 2 other 2001 Z71 pickups and have never had to clean anything.. gas is bought for the tahoe at the same places I fill my other trucks at.. anyone have an idea on how to fix this problem and why it gets so dirty in such a short period of time?
Why does my engine blow by?
Most modern engines draw engine "blow by" back through the carburetor/throttle body for a reburn of the vapors (PCV). It's part of the emissions control and it's normal. The fuel also turns to a varnish or gum over time. It attracts dust from the engine compartment and incoming air which compounds the problem.
bgbdwlf2500
So I followed a video on youtube, looked pretty straight forward. Hold the TB blade open (by hand), wipe out the crud, be careful of how much TB cleaner you use. So that's what I did, for the most part I sprayed the cleaner onto a rag and wiped all the gunk out. Started truck, it idled fine so I clocked back in and went back to work.
GhostWriter
Well, it might have been better if you had used the gas pedal (key on, engine off) to open the butterfly, for cleaning. Even then, the gunk removed may have resulted in more than one re-learn attempts to get things back in order.
bgbdwlf2500
Well, it might have been better if you had used the gas pedal (key on, engine off) to open the butterfly, for cleaning. Even, then, the gunk removed may have resulted in more than one re-learn attempts to get things back in order.
bgbdwlf2500
Well, don't be hasty. There are some real experts on here that haven't chimed in, yet.
carnau
So I followed a video on youtube, looked pretty straight forward. Hold the TB blade open (by hand), wipe out the crud, be careful of how much TB cleaner you use. So that's what I did, for the most part I sprayed the cleaner onto a rag and wiped all the gunk out. Started truck, it idled fine so I clocked back in and went back to work.
carnau
Tech 2's have dropped so much in the last few years it is crazy. I remember I spent almost 4k on mine 15 years ago lol.
bgbdwlf2500
Tech 2's have dropped so much in the last few years it is crazy. I remember I spent almost 4k on mine 15 years ago lol.
Step 1 – Open hood and pop off plastic engine cover
That behemoth of a top cover on your Vortec V8 is held on by only two tabs. Gently lift the front until it pops up from its post, then reach under and toward the rear of the cover to pop the back tab. (It's so easy, a US Congressman could do it!)
Step 3 – Remove air intake tubing
At each end of the intake tubing, you'll see a worm-drive clamp. Loosen both clamps at the air cleaner and TB unit. There will also be a tab at the far left side rear. Simply pop that off. Finally, unplug the sensor plug on the intake tube.
Step 4 – Remove power leads to the throttle body
Simply push down on the gray clip tab, and remove the entire plug. You should not have to remove the pink clip.
Step 5 – Remove the throttle body assembly
Using a 10mm wrench, remove the two nuts and two bolts. Then, slide the TB off the studs.
Step 6 – Inspect O-ring and replace if needed
The O-ring should be intact; however, if it has any cuts, abrasions, or is just plain grungy, you should have a new gasket in the new throttle body kit.
Step 7 – Install the new (or refurbished) throttle body
Simply line up the stud screws and slide the unit in place. Tighten the nuts and lower bolts in a crisscross pattern until tight. Do not over tighten! There is no torque spec for these, so use common sense when tightening. Plug the sensor plug in, and secure it with the gray clip.
Step 8 – Reinstall air intake assembly and cover
Install the plastic air intake tubing assembly, tighten the worm-drive clamps, and push the PCV valve back in place. Simply line up the front and rear tabs on the engine cover. Then, push down firmly until it snaps into place. Plug in the sensor at the air cleaner end of the intake.
Why does brake fluid lock up?
The moister can pool in the lowest point ( the caliper) causing corrosion. In extreme cases of neglect the water in the calipers can heat and expand causing the caliper to lock up.
Can you use carb cleaner on a throttle body?
Make sure that you use throttlebody cleaner and not carb cleaner. Carb cleaner will take the coating off all the inside of the throttlebody. The advantage of the power bleeder Is that you just pump it up and open the bleeders, no pedal pumping needed.