For example, to perform a throttle relearn on a 2008 Silverado 5.3L, select and run the Idle Learn Reset test. Then start the engine and allow the ECM time to begin to learn. Additionally, the Mentor Touch Scout supports Throttle Sweep and Throttle Position tests to verify proper operation of throttle components.
How to replace a throttle position sensor?
How to Replace a Throttle Position Sensor. Remove the battery Before you begin, detach the negative terminal connection from the battery. This will prevent you from receiving undesired shocks as well as causing harm to other components under the hood. Unplug the Previous Sensor
How do you adjust the throttle position sensor?
TPS – Throttle Position Sensor Adjustment
- Loosen the jam nut and unscrew the throttle stop screw all the way so that the throttle blade closes fully against the throttle body itself.
- Turn the stop screw back in until it just touches the linkage, then turn in ¼ turn more. ...
- Tighten the jam nut while holding the stop screw in place to prevent it from moving.
- Unplug TPS
Should I replace the throttle position sensor?
The throttle position sensor not only helps to control the fuel and air mixture in your engine but also helps with shifting gears. While this part is meant to last the lifetime of your vehicle, sometimes it can fail and will need prompt replacement.
How do I replace the throttle position sensor?
- Back probe leads (optional)
- Free repair manuals provides free online repair manuals for certain makes and models
- Protective gloves
- Safety glasses
- Screwdriver
- Voltmeter (optional)
How do I relearn my throttle position sensor?
How to Reset Throttle Position SensorPut the key in the ignition.Turn the key to the On position, without cranking the engine. Wait a few seconds, then turn it off.Repeat the second step.Crank the engine.Pull the parking brake.Set the gear lever in Drive.Wait 5-10 minutes.
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.
How do you calibrate a throttle position sensor on a Chevy?
3:224:22How to Calibrate Throttle Position Sensor Using a Multimeter (Set TPS)YouTubeStart of suggested clipEnd of suggested clip45 volts and then as you apply throttle. You should see the voltage. Increase steadily up to aboutMore45 volts and then as you apply throttle. You should see the voltage. Increase steadily up to about four and a half volts uh or all the way up to five we should be good to go here.
How do I reset my throttle body relearn?
Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds.
How do you reset the throttle position sensor on a Chevy Silverado?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
What happens if you don't relearn your throttle body?
What happens when you replace the throttle body? If you replace the throttle body, the PCM won't know and will continue to use the adaptive settings as if the carbon buildup is still in place. If you don't do a relearn procedure, the PCM will “hunt” for a new baseline idle.
How do you calibrate a new throttle position sensor?
4:0310:54How to install & calibrate a new Throttle Position Sensor (TPS) #1208YouTubeStart of suggested clipEnd of suggested clipWe now need to calibrate the unit. So as you can see there is some angular movement angularMoreWe now need to calibrate the unit. So as you can see there is some angular movement angular adjustment of that TPS unit and with the throttle at the idle.
Do you need to calibrate a new throttle position sensor?
Once you have fitted a Throttle Position Sensor, or TPS, you will need to calibrate it from within MEITE. First, be sure you have correctly wired, and assigned the throttle sensor signal input to "TPS Raw" in the Analog Settings.
How do you relearn a Chevy idle?
After the engine is warm, switch the air conditioning on and off, and then put the transmission into the "drive" position. These actions complete the full idle relearn procedure.
How do you adjust the idle on a GM throttle body?
3:015:54How to: GM TBI Idle Adjustment - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you'll just I took a drill bit drilled it out and it should be a t25 to adjust it we will turn itMoreSo you'll just I took a drill bit drilled it out and it should be a t25 to adjust it we will turn it clockwise. I think to advance the idle.
What happens if you replace throttle body?
If you replace the throttle body, the PCM won’t know and will continue to use the adaptive settings as if the carbon buildup is still in place. If you don’t do a relearn procedure, the PCM will “hunt” for a new baseline idle.
What is a fly by wire throttle body?
Many car makers including GM started installing fly by wire electronic throttle bodies. In those vehicles, the “gas” pedal isn’t connected to the throttle body by a cable. The pedal simply provides an electronic signal, telling the throttle body how much acceleration you’re requesting.
What to do after cleaning a GM throttle body?
After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn. After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn.
Can you throttle relearn without a scan tool?
Throttle relearn can also be done without a scan tool, essentially by letting the vehicle idle in park for several minutes and allowing time for the ECM to learn. See appropriate service information for vehicle specific procedures and details if you wish to perform a throttle relearn in this way. Information provided by Mac Tools.
How to reset a dtc?
Remove negative battery cable for 20 minutes to reset all DTCs. 2. Start engine, run in park for 3 minutes. -MIL did not come on. -Engine starts at about 1200rpm, then slowly idles down to 800 rpm and back up to a steady 1000rpm. 3. Remove key for 60 seconds. 4. Start engine, run in park for 3 minutes.
Does P0121 have TPS?
I read up on P0121 and saw that it involves the TPS integrated into my Throttle Body. I decided to clean to TB before spending ~$200 on a replacement.