Nissan Maxima – (RickDeacon / Shutterstock) The most common causes for slow acceleration in Nissan Maxima are clogged air filter, dirty mass air flow sensor (MAF), clogged fuel filter, fuel pump malfunction, faulty oxygen sensor, dirty throttle body, worn spark plugs and clogged catalytic converter.
Full Answer
Can a bad clutch cause a Nissan Maxima not accelerate?
Although the manual transmission is going away, if you happen to have a Maxima equipped with one, a bad clutch can cause it not to accelerate. The clutch is responsible for making a direct connection between the engine (via the flywheel) and the transmission (via the input shaft). When the clutch can’t hold on anymore, it’ll start to slip.
What happens if your Nissan Maxima is low on transmission fluid?
If your Maxima is too low on transmission fluid, it’ll will no longer be able to transfer power to the rear wheels. The power goes to the torque converter, and that’s the end of the line.
Why does my car have hesitant acceleration at the first stop?
At the first stop after an hour or more of highway driving, the car has very slow/hesitant acceleration at low-rpm unless a lot of gas is given. After getting the car to rev-up by pressing the gas hard, the car operates normally. However, unless the engine revs up, the hesitant acceleration can continue for several stops/starts.
Why won't my car accelerate?
What happens if you run a car without coolant?
Is PCM a component that fails?
About this website
Is there a recall on 2007 Nissan Maxima?
2007 Nissan Maxima Recalls 114, 'THEFT PROTECTION. ' DURING AN INSPECTION OF SOME VEHICLES AT THE ASSEMBLY PLANT, IT WAS FOUND THAT THE STEERING WHEEL WAS LOCKED WITH THE IGNITION KNOB IN THE 'OFF' POSITION BUT THE VEHICLE TRANSMISSION NOT BEING IN THE 'PARK' POSITION.
Why is my Nissan Maxima jerking?
An indication that a vehicle is not receiving the right mixture of air and fuel is if the vehicle jerks or surges forward at high speed. Several components of the fuel or air intake system could cause this jerking or surging sensation to happen. Issues within these systems can also cause fuel economy to worsen.
Do Nissan Maximas have transmission problems?
While other Nissan models, such as Altima, Sentra and Rogue, became known for their CVT transmission issues, drivers of Nissan Maxima cars have reported several recurring CVT transmission problems. These CVT issues include lurching, acceleration issues, vehicle overheating and premature transmission failure.
How do I get my Nissan Maxima out of limp mode?
Turn ignition to on position for 2 seconds turn to off for 10 seconds, do that twice, then tap the gas pedal 5x, wait 7 seconds then push the pedal to the floor and hold until check engine light flashes. Don't let it up until it starts flashing.
Why is my Nissan Altima sputtering?
Fuel injector nozzles can become clogged over time, which can lead to a sputtering engine, slow acceleration and the car not having enough power. Fuel injectors can be cleaned if the problem is caught early, but as the conditions worsens, the injectors may have to be replaced.
What year did Maxima avoid?
40 years ago, Nissan debuted their Maxima. Ever since then, it has been a go-to model of choice for many Nissan customers. During those 40 years, only 2004 to 2008 are the models to avoid.
How many miles can a 2007 Nissan Maxima last?
The Nissan Maxima is a performance sedan built to last. The average lifespan of the Maxima is 150,000 to 200,000 miles. This means that with the average 15,000 miles per year driven, you can expect 10 – 13 years of service or more with proper usage and maintenance.
What years did Nissan have transmission problems?
Generally, the issues have been reported between 2012/2013 and 2018. There were some problems in 2003 when Nissan first began using this transmission and in the 2007-2012 CVT generation. Specific models include the Murano, Sentra, Altima, Rogue, Versa, and Versa Note.
What sensors can cause limp mode?
If one of the sensors, such as the MAF, MAP, TPS or speed sensors are sending improper signals to the computer, limp mode can activate. Failed fuel injectors, coil packs and worn out spark plugs can also cause it.
How do you reset the transmission control module on a Nissan?
After turning on the car, you must shift through automatic transmission gear at least two times. In manual cars, shifting between drive and reverse should occur three times. The gear shifting must continue for at least 10 miles, automatically reset the transmission control module.
Will driving in limp mode damage car?
Will driving in limp mode damage the car? Driving under limp mode for such a long period could result in car damage. Most manufacturers suggest that you can only drive a car in limp mode to the closest shop, mechanic, or your house. Avoid driving in limp mode if the engine overheats.
What problems does the Nissan Maxima have?
A list of some of the most common issues Maxima owners have to deal with.Nissan Automatic Emergency Braking (AEB) Problems. ... Sunroof Rattles and Explodes. ... Nissan Vehicles with Recalled Takata Airbags. ... Timing Chain Defects. ... Steering Wheel Locked. ... EVAP Clogs and Gas Spills. ... Premature Automatic Transmission Failure.
Are Nissan Maxima CVT transmissions reliable?
I've owned four Maximas and the cvt has performed flawlessly on all of them. I did have a '13 Altima that had terrible cvt problems … but the difference of the cvt performance in the Maxima was obvious. The Pathfinder also had severe CVT issues back then, but I am not aware of any inherent problems on the Maxima..
Is a Nissan Maxima a reliable car?
Nissan Maxima Reliability Rating Breakdown. The Nissan Maxima Reliability Rating is 3.5 out of 5.0, which ranks it 9th out of 12 for fullsize cars. The average annual repair cost is $540 which means it has lower than average ownership costs.
How much does it cost to replace a transmission on a Nissan Maxima?
The cost of a new Nissan Maxima transmission could be over $3,500 depending on the vehicle, however, transmission services such as fluid changes and a transmission fluid flush are considerably less expensive, in some cases costing less than $150.
Common Reasons Your Nissan Maxima Wont Accelerate
If your Nissan Maxima won't accelerate, that is a serious cause for concern. There are a lot of different reasons that can cause this. Diagnosing the issue can be narrowed down by whether the engine is still revving when you push the gas or not. There is a section for each scenario with likely causes
Nissan Maxima Questions - Car will not accelerate after 40 mph - CarGurus
Thank you. The noise does not sound like wheel bearing. The noise is like the wheel robbing into something. I will check the fuel filter. Somebody suguested to check the transmission selenoid but I am not sure if my car has one or if it has another name.
SOLVED: Vehicle won't go over 25 mph. help!! - Fixya
it is not how many miles but the type of driving. here is a OBD2 drive cycle test. Generic OBD II "Drive Cycle" Most OBD II ("On-Board Diagnostics II") diagnostic monitors will run at some time during normal operation of the vehicle.
My car won't accelerate over 40 mph and check engine ligh...
Q: My car won't accelerate over 40 mph and the check engine light is on My car has 152000 miles. My car has an automatic transmission. Hi there. In many cases, when you have an issue with the car accelerating and the check...
Why is my Maxima not accelerating?
If something has gone wrong in the transmission, your Maxima may not be able to accelerate any more. If it can no longer shift, it could be caused by a solenoid/valve body has gone bad, clutch packs, debris, and much more. Automatic transmission are very complicated.
What happens if you break a drive shaft on a Nissan Maxima?
If you’ve broken a drive/axle shaft, your Nissan Maxima’s transmission has no way to turn the wheels anymore. If this were the case, there would not be any movement whatsoever from the vehicle. You also wouldn’t feel the slight jerk your Maxima as you put it into gear.
What happens if your Maxima is too low on transmission fluid?
Transmission Fluid Low. If your Maxima is too low on transmission fluid, it’ll will no longer be able to transfer power to the rear wheels. The power goes to the torque converter, and that’s the end of the line. You should check the transmission fluid immediately.
What is the purpose of the timing chain on a Maxima?
The timing chain (or belt) is responsible for keeping the upper valve train synced with the crankshaft. This is vital for spark timing. If the timing is off a little and the engine still runs, the timing belt may have skipped. If it has jumped too much the Maxima may not even fire.
Why does my Maxima have a vacuum?
Your Maxima’s engine creates a vacuum as it runs. The amount that is created is carefully thought out during the engine design process. When there is too much vacuum, it creates a situation where air is not coming in and being read by the MAF sensor, which causes the vehicle to run wrong and not accelerate.
Can a bad fuel filter cause a Maximas engine to bog down?
A bad fuel filter will not let enough fuel into the Maximas fuel injection system to support operation above a certain demand on the engine. It just can’t provide the fuel pressure. If this is the case, like the catalytic converter, it’ll feel like everything is fine until you hit a certain speed, and then it’s going to bog down again.
Does the Nissan Maxima accelerate?
Conclusion: Nissan Maxima Not Accelerating. As you can see, there are a lot of reasons that your Nissan Maxima may not accelerate. Good luck diagnosing yours. If there is anything that you can add, please feel free to leave a comment.
1. Clogged air filter
If the air filter is dirty in your Nissan Maxima, it can have a negative effect on the performance of the engine, as less air passes through the dirty filter which suffocates the engine. This ultimately also increases fuel consumption. In the worst case, the engine can stall if the air filter is extremely clogged.
2. Dirty or faulty mass air flow sensor (MAF)
Defective or dirty mass air flow sensor (MAF) in your Nissan Maxima can result in loss of power, uneven engine running, erratic idling, misfires, poor exhaust emission values including black smoke. The mass air flow sensor is part of the engine’s intake system and is located between the air filter box and the throttle valve.
3. Clogged fuel filter
If the fuel filter is clogged in your Nissan Maxima, not enough fuel can get into the engine. This causes loss of power and jerking of the vehicle when accelerating. In worse case scenario, engine cuts out while driving due to insufficient fuel supply.
4. Clogged catalytic converter
The catalytic converter is part of the exhaust system in Nissan Maxima and its main purpose is to convert exhaust gases that are harmful to health and the environment into less harmful byproducts. Over time, toxins accumulate and clog up the catalytic converter, especially if the vehicle has racked up a lot of miles.
5. Faulty oxygen sensor
The oxygen sensor in Nissan Maxima monitors the level of pollutants in the engine’s exhaust gases and reports the data to the control unit that continuously adjusts the air to fuel ratio in the engine.
6. Dirty throttle body
Dirty throttle body can also be the cause of slow acceleration in your Nissan Maxima. The common signs of dirty throttle body are poor engine performance, erratic idle, the engine react poorly to movements of the accelerator pedal, and the engine sputters or stalls.
7. Faulty throttle position sensor (TPS)
The throttle position sensor or TPS is used to determine the opening angle of the throttle valve. The information obtained is sent to the control unit and contributes to the calculation of the amount of fuel required.
Why won't my car accelerate?
There are a lot of possibilities, depending on whether it won’t accelerate because the engine doesn’t have the power , or if it doesn’t accelerate because there is a problem in the drivetrain, or if it simply isn’t trying to accelerate. I’ll take a guess that it is the latter.
What happens if you run a car without coolant?
Depending on how hot the vehicle got and how long the engine ran without coolant, this may have caused some serious engine damage. Commonly, when this happens an engine may get too hot to the point where a cylinder head...
Is PCM a component that fails?
Your question for replacement cost of your vehicle's PCM (powertrain control module, is difficult to answer (new, remanufactured, used). Typically, the PCM is not a component that fails, and will most likely require programming once replaced. It could...
What causes a car to shake when accelerating?
Here are some of the problems that can cause a vehicle to shake when accelerating that can come from the engine: Vacuum Leak. Bad MAF Sensor.
What happens if the motor mount goes out?
If the motor mount goes out, the vehicle will shake quite a bit when you accelerate. It can still get worse though. A motor mount that has broken will allow the engine to roll around under the hood, and you’ll hear a clunking sound. There’s more than one motor mount on a vehicle.
What does a bad motor mount feel like?
Vehicle Speed: A bad motor mount is going to be felt when immediately accelerating. You should feel a vibration as you let off the gas, although it may not be as pronounced. The motor mount is responsible for connecting the Nissan Maxima’s motor to the chassis. It also needs to absorb a significant amount of vibration.
What causes a CV joint to go bad?
The inner CV joint is most likely to be the part of the CV shaft that has gone bad. More often than not, a bad CV joint is caused by a torn boot. The protective boot goes over the CV joint and keeps oil in and debris out. It is really easy to tell if the boot is bad. Just take a look.
Can lug nuts cause a vehicle to shake?
It depends on the vehicle, wheel in question, and how loose they are as to exactly what speed that would be. Lug nuts can cause a vehicle to shake when accelerating.
Acceleration problem
My 2009 has a problem accelerating from a dead stop. I can put the pedal to the floor and the car barely rolls until it hits about 10 mph and then it accelerates fine. The idle is fine. Runs fine once it it rolling, but literally almost does not move from a dead stop. I am afraid if I was stopped on a hill the car would not move.
Re: Acceleration problem (Weberrider)
Have you had the TCM/ECM program update recall performed? About two weeks ago I had mine re-programmed during its regular scheduled service. The hesitation I experienced when accelerating from a stop disappeared.
Re: Acceleration problem (robf70837)
The only recall notice I have received is for the steering. I would not call this a hesitation. The car barely moves. It take about 5 seconds to reach 10 mph.
Re: Acceleration problem (Weberrider)
This was the reason I decided to finally sell my pearl glow nissan maxima. Loved that car. I would press the gas to the floor and it barely moved. When it finally was accelerating. It was extremely slow though. Barely reaching 40-45 mph and struggled. So I sold it. Anyways, pressing pedal to the floor I always considered extreme.
Re: Acceleration problem (casperfun)
Just take it to the dealer (on a day when the problem is easily reproducible) and have the service manager drive it. He will schedule an appointment for the TCM/ECM update and/or whatever else is necessary to fix the problem. This is definitely not normal and is covered under warranty.
Re: Acceleration problem (goin' rogue)
The problem was a stop switch that tells the transmission that the car has stopped and must resume movement in a lower range in the transmission. The switch was failing and the trans did not get the signal that I had stopped. Basically like starting in 4th gear from a dead stop.
Re: Acceleration problem (Weberrider)
Thanks for the update. Just out of curiosity, were the repairs done under warranty, or not?
Why won't my car accelerate?
There are a lot of possibilities, depending on whether it won’t accelerate because the engine doesn’t have the power , or if it doesn’t accelerate because there is a problem in the drivetrain, or if it simply isn’t trying to accelerate. I’ll take a guess that it is the latter.
What happens if you run a car without coolant?
Depending on how hot the vehicle got and how long the engine ran without coolant, this may have caused some serious engine damage. Commonly, when this happens an engine may get too hot to the point where a cylinder head...
Is PCM a component that fails?
Your question for replacement cost of your vehicle's PCM (powertrain control module, is difficult to answer (new, remanufactured, used). Typically, the PCM is not a component that fails, and will most likely require programming once replaced. It could...