2004 ford f150 throttle position sensor reset

How do you reset the throttle body on a 2004 Ford f150?

"Turn the key to the on position but DON'T start the engine. Now press the gas peddle to the floor SLOWLY and let it come up/back as fast as you can, turn key to the off position. Now do this two more times."

How do you relearn a throttle position sensor?

1:082:42Throttle Body Relearn: When Should I Reprogram My Car's ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.

Do you have to reset computer after replacing throttle position sensor?

After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.

How do you relearn a Ford throttle body?

Turn the air conditioning on and allow the engine to idle for at least one minute. Release the parking brake. With your foot on the brake pedal and the A/C still on, put the vehicle in "D" (Drive) and allow the engine to idle for at least one minute. Drive the vehicle to complete the relearning process.

How do you reset the throttle position sensor on a Ford f150?

Resetting the throttle position sensor is a simple process that can be done in just a few minutes.Find The Throttle Position Sensor. ... Disconnect The Electrical Connector. ... Unhook The Negative Cable From The Battery. ... Remove the Screws. ... Reconnect The Battery and Start The Engine. ... Regularly clean the throttle body and sensor.More items...•

How do you calibrate a TPS sensor?

3:224:22How to Calibrate Throttle Position Sensor Using a Multimeter (Set TPS)YouTubeStart of suggested clipEnd of suggested clip45 volts and then as you apply throttle. You should see the voltage. Increase steadily up to aboutMore45 volts and then as you apply throttle. You should see the voltage. Increase steadily up to about four and a half volts uh or all the way up to five we should be good to go here.

What happens if you don't relearn your throttle body?

What happens when you replace the throttle body? If you replace the throttle body, the PCM won't know and will continue to use the adaptive settings as if the carbon buildup is still in place. If you don't do a relearn procedure, the PCM will “hunt” for a new baseline idle.

How do I reset my electronic throttle control manually?

Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.

How do you reset throttle body after replacing?

Leave the key off for a moment, turn the key to the "On" position again, wait 3 seconds, and press the accelerator 5 times in 5 seconds. Wait 7 seconds, and hold the accelerator down. The check engine light should start blinking, continue to hold pedal down until it stops blinking. You can then start the car.

Do you have to calibrate a throttle body?

Once you have fitted a Throttle Position Sensor, or TPS, you will need to calibrate it from within MEITE. First, be sure you have correctly wired, and assigned the throttle sensor signal input to "TPS Raw" in the Analog Settings.

How do I reset my throttle actuator?

Make sure that the accelerator pedal is fully released. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds.

What is a reset throttle position sensor?

A reset of the throttle position sensor grants fast airflow in the engine. In short, it is a tiny sensor part that helps your Ford truck to run faster when you press the accelerator. The throttle position sensor also helps you get the ideal idle if it works with no bad symptoms. Now, grab all the tools down below and move to the actual process.

How to turn off a Ford truck?

After that, it’s time to turn off the truck by turning the keys on a counterclockwise position. Take a break for a minute. Again, turn on your Ford truck by twisting the key. Then, when the beep sound stops, you need to press the accelerator pedal in the same manner. Shut down your truck and wait for a moment.

How long should a Ford truck be idle?

Now, you need to turn on the Ford truck. After that, the Ford truck should be in an idle position for 10-15 minutes. We find it very effective to easily reach the full operating temperature of a healthy truck. You just need to keep your truck in the same state without doing anything to get the perfect full hot values.

What to do before resetting Ford?

Taking safe equipment is an essential thing you should do before trying resetting processes. As you’ll contact Ford trucks parts, hand gloves and clean clothes are a must item to wear. Also, ensure a good distance to electric parts that can damage severely.

Can you break the throttle sensor on a Ford truck?

Also, resetting the throttle sensor on the Ford truck is a big task that needs professional tools. For that, a fine quality tool that doesn’t break or crack nuts of Ford truck. Even if the tools cost more, still bear in mind they help most when resetting the throttle position sensor.